Activity
From 08/01/2025 to 08/30/2025
08/29/2025
- 08:36 PM MitySOM-A5 PCB Development: RE: PCIe connection to Computer MB
- Hello,
yes, actually it is worse than that.. the FPGA can only tolerate about 10mA, and must be less than 1.2V d... - 06:50 PM MitySOM-A5 PCB Development: RE: PCIe connection to Computer MB
- Hi Keith,
I don't think you can drive it in the FPGA (PCIe needs to be up fairly quickly and may need to be there ... - 12:36 AM MitySOM-A5 PCB Development: RE: PCIe connection to Computer MB
- Hi,
Actually, there is another issue, in EP mode, the Presecence signals, PRSNT2_*X1*# and PRSNT2_*X4*# need to ... - 06:25 PM MitySOM-A5 FPGA Development: RE: What is the recommended version of Quartus for MitySOM_A5?
- Hello Tom,
Thanks for the explanation.
Me and Keith, we are working together. We've ordered a cable (PCIe edge on... - 06:13 PM MitySOM-A5 FPGA Development: RE: Fail to program device
- Mike, please see attached log of the compilation
- 06:07 PM MitySOM-A5 FPGA Development: RE: Fail to program device
- Hello Mike,
No I didn't made any changes. I removed everything. I clone again, navigate to directory and run comma...
08/28/2025
- 08:58 PM MitySOM-A5 FPGA Development: RE: Fail to program device
- Did you make changes to the design to switch to FPGA first as described in my previous post? Or are you just trying t...
- 08:28 PM MitySOM-A5 FPGA Development: RE: Fail to program device
- Hello Mike,
Thanks again for your help!!!
I've followed the instructions that you send me yesterday. The command ... - 04:36 PM MitySOM-A5 FPGA Development: RE: Fail to program device
- > But, since we are using FPGA ONLY (no HPS), should this instructions to be applied, or we can generate .jic only??
... - 02:16 PM MitySOM-A5 FPGA Development: RE: Fail to program device
- Hello Mike,
I'm going to follow the instructions.
But, since we are using FPGA ONLY (no HPS), should this instruc... - 08:13 PM MitySOM-A5 FPGA Development: RE: What is the recommended version of Quartus for MitySOM_A5?
- Hello Maxim,
We will coordinate this with Engineering Management and get back to you mid-next week. Since I know y... - 02:06 PM MitySOM-A5 FPGA Development: RE: What is the recommended version of Quartus for MitySOM_A5?
- Hello Mike,
Thanks for your help. I've got the attached reference.
I have a question: do you have any estimation fo... - 01:42 PM MitySOM-A5 FPGA Development: RE: What is the recommended version of Quartus for MitySOM_A5?
- Maxim,
Attached is our reference design for 25.1. This is not formally released yet as we are still working on wra... - 03:23 PM MitySOM-A5 PCB Development: RE: PCIe connection to Computer MB
- Hello,
Samtec does offer Cross-Over type of cable in their Gen 4 and Gen 5 cables.
https://www.samtec.com/pro... - 09:45 AM MitySOM-A5 PCB Development: RE: PCIe connection to Computer MB
- Hi Keith,
Your concern is valid. You will need some sort of "cross-over" cable to swap Tx/Rx lines, etc.
I am ...
08/27/2025
- 09:18 PM MitySOM-A5 FPGA Development: RE: Fail to program device
- Maxim,
Please use the instructions found here for programming the QSPI NOR Flash (from the command line): https://... - Hello
I've just got MitySOM_A5 Dev. Kit and started to work on it.
I'm trying to create my own project based on Cri... - Hello,
I'm trying to create an example design for AXI MCDMA for PCIe. But this IP core is exist in Q25.x versions on... - 08:51 PM MitySOM-A5 PCB Development: RE: PCIe connection to Computer MB
- however I think the Tx and Rx lines need to be swapped w.r.t. the connector between EP and RP ... we cannot change th...
- 08:20 PM MitySOM-A5 PCB Development: RE: PCIe connection to Computer MB
- okay I see there are some 0 ohm resistors to feedback the REFCLK+/- (PCIe_CLK) in end point mode... R81 and R83 on ca...
- Hello,
We are working on testing the PCIe interface on the Mighty-Mini Agilex-5E dev kit.
The PCIe x4 connector... - 08:28 PM MitySOM-A5 PCB Development: RE: FAN enable
- Keith,
The FAN_EN GPIO can be enabled by exporting the GPIO in sysfs and driving it high.... - Hello,
Is there a Linux software command to enable the +5V Fan from the HPS ? or a register we can write to to ...
08/22/2025
- 06:59 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: RE: realtime linux on am62x
- I got the linux-cl-ti-rt-6.6 recipe working...
08/21/2025
- 06:19 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: MitySOM-5CSX development kit
- Ok Mike,
Thanks.
Best regards,
John
08/20/2025
- 05:14 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: MitySOM-5CSX development kit
- John,
Our latest reference design for the 5CSx is on Quartus Prime version 23.1, therefore you should be good! The... - Hi! I am just starting out with the MitySOM-5CSX development kit and have the following tools set up:
1. Quartus p...
08/15/2025
- 05:37 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: RE: realtime linux on am62x
- > Still working on the yocto recipe part. It built but the kernel was missing the RT configs. Probably missing someth...
- 03:55 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: RE: realtime linux on am62x
- Please do.
There is a chance we won't need it, but I would like to have it my back pocket in the case that we do... - 03:27 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: RE: realtime linux on am62x
- Hi Nathan, I never heard back from you so this dropped off my todo list. I can try to pick it back up next week to s...
- 03:18 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: RE: realtime linux on am62x
- Hi Jon,
Just checking in, we are rapidly approaching being able to know if we need this or not. I thought I would...
Also available in: Atom
Go to top
