Activity
From 07/11/2023 to 08/09/2023
08/09/2023
- DK 04:12 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Dmitry Kolotsei wrote in message#6457:
> Hi Mike
> ...
This request is actual
Br, Dmitry - DK 03:42 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- "Make clean" does not clear everything to repeat "make uboot". What to do?
I found make scrub_clean
- DK 03:26 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi, Mike
And further. I'm not very good in make.
"Make clean" does not clear everything to repeat "make uboot". What to do?
Br, Dmitry. - DK 02:49 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi Mike
Thank you for help. I has some progress!!!
I was in project folder, but Makefile was absent in it.
I got Makefile from Mitysom project, got UBoot compiled and write it to SDcard.
I see not succussed attempts to reconfigur... - DV 01:15 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi Dmitry,
Try to CD into your software/bootloader directory and just run:
make TGZ=uboot-socfpga.tar.gz SOCFPGA_BOARD_CONFIG=mitysom_a10s_dsc_defconfig
Our example expect that you are using our FPGA reference design, which has a ... - DK 01:08 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi, Mike
Thank you for reply.
I did the instruction https://support.criticallink.com/redmine/projects/mitysom_a10s/wiki/Building_U-Boot_for_MitySOM-A10S
And got error on compilation
How I can correct?
Br, Dmitry. - MW 11:44 AM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi Dmitry,
mitysom_a10s_dsc_defconfig
Follow these instructions when using Quartus 18.0.
https://support.criticallink.com/redmine/projects/mitysom_a10s/wiki/Building_U-Boot_for_MitySOM-A10S
-Mike
- DK 11:07 AM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Which default config I need to use?
- DK 10:46 AM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi, Dan
I got dtb from working SDcard image.
I using mitysom_a10 branch for UBoot compilation.
I prepared .config with menuconfig as I understand.
I got error during UBoot compilation(see attachment).
How I can to reach succes...
08/08/2023
- DV 06:32 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi Dmitry,
I believe the DTS is auto generated for u-boot from the quartus tools. I think the bsp-editor is what generates it.
Dan - DK 04:37 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi, Dan
Thank you for reply.
Can I use DTS as in attachment for "mitysom_a1" branch? I get him from ArrowElectronics.
If not than where I can get right DTS or DTB for UBoot compiling?
Thank you very much in advance.
Br, Dmitry. - DV 02:17 PM Software Development: RE: Replacement UBoot 2014.10 on 2021.04
- Hi Dmitry,
The ADRV9009 demo was built using quartus 18.0 and using uboot 2014.10. Critical Link has a uboot 2014.10 that supports programming the PLLs the branch is called "mitysom_a10": https://support.criticallink.com/gitweb/?p=u-b... - Hi All
I have working FPGA project based on https://github.com/ArrowElectronics/arrow-adi-intel-psg/wiki/ADRV9009-Platform-User-Guide
I have a task to change the configuration of external generators (SI5338) on Critical Link board in... - DK 11:26 AM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi, Dan
It is my debug project
Br, Dmitry
08/07/2023
- DV 02:53 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dmitry,
You're "After correction.jpg" looks to be correct. Have you also checked if U15 CLK1 behaves the same way?
Can you send me your FPGA project or a simplified version for me to review?
Thanks,
Dan
08/05/2023
- DK 04:10 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi, Dan
I returned to start Mitysom project downloaded from git.
After first compilation I see inconsistency between Pin Planner and Assignments from one side and results in Input Pins (Fitter report) on another side. You can see all...
08/04/2023
- DV 05:42 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dmitry,
Your pin out and clock project look to be correct. If you're seeing clocks on the output of U15 then I would say it's programmed correctly. To double check that the FPGA receives it can you route one of the clocks to an FP...
08/02/2023
- DK 04:36 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi
You are right. My board is rev 4.
I changed the U15 configuration and currently I use CLK0 (pins R24/R23) and CLK1 (pins AB15/AA16).
But result is the same ((
I see signals on the pins of SI5338, but don't see the signals in sig...
08/01/2023
- DV 02:32 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dmitry,
The revision is at the end of the 80-# number of the white tag. For example, 80-001124RC-*4*A is a rev 4 of the 80-001124 part number.
My recommendation is the following:
* Use U15 CLK0 and CLK1 because these don't move... - DK 08:03 AM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi
I have rev 9 board and working in accordance with datasheet pointed by you.
You can make sure in that by screenshots attached by me.
Best regards.
07/31/2023
- DV 06:15 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dmitry,
It looks like you are using the pinout from the rev 8 of our SOM but I believe you have an earlier rev of the SOM.
Your SOMs should follow the clocking that is in our datasheet (Figure 2).
Datasheet: https://www.crit...
07/30/2023
- DK 02:21 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dan,
Thank you for the reply.
I added proposed assignments.
I recreated the differential signals on pins. Quartus automatically added paired signals with '(n)' in the end of names.
I got state when there are not any question sig...
07/28/2023
- DV 05:33 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dmitry,
Do you have differential terminations enabled for these signals? If not that might be the issue. The syntax for adding these to qsf looks like the following: - DK 05:11 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi all,
SI5338 is working correct, I see right frequencies on output pins (CLK0A, CLK0B, CLK2A, CLK2B) of chip U15.
But FPGA project does not receive these signals.
I coded simple counter (module cycle_gen) and instantiate it on eac...
07/19/2023
- DK 09:04 AM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi, Dan
Thank you very much for help.
PLL is reconfigured.
Dmitry
07/18/2023
- DV 06:46 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hello,
I have found a deficiency in our instructions, the register header files needs to be manually updated in order to enable the outputs. I updated the steps in the https://support.criticallink.com/redmine/projects/mitysom_a10s/wik... - DK 03:20 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- h-files for generating bin-files
- DV 03:04 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dmitry,
Can you please attach your header files that you used to generate the 2 binaries as well?
Thank you,
Dan - DK 02:54 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi, Dan
Thank you for help.
This image is started.
Next step. I prepared U14PLL.bin in accordance with recommendation on page https://support.criticallink.com/redmine/projects/mitysom_a10s/wiki/Customizing_the_On_Board_Silicon_Lab... - DV 02:03 PM Software Development: RE: Mitysom a10s does not start under U-Boot 2021.04
- Hi Dmitry,
We have just recently found an issue with the released SD cards for the 480KLE version of the SOM, which causes them not the boot. I have uploaded a new version, which fixes the boot issue.
Please try the following SD ca... - Hi all.
I need to change the on-board PLL configuration to get the frequency 322.265625 MHz.
I am trying to use U-boot version 2021.04 with board A10S-P9-X5E-RI-SA. Because, as I know, only U-Boot version 2021.04 supports the loading...