Mity CPU Platforms

10/09/2025

MW 11:34 AM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Building the MitySOM-5CSX

Hi John,
On the main wiki landing page, https://support.criticallink.com/redmine/projects/mityarm-5cs/wiki, there are links for full SD pre-built SD cards (which include images of the reference filesystems) as well as a tar-ball of th... Michael Williamson

JI 11:30 AM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Building the MitySOM-5CSX

Hi Seth,
As mentioned, I have been able to build uboot. I am now studying the steps to build the file system with Yocto. It appears that there a quite a few steps here and, as usual, with Linux, opens the flood gates for mistakes.
... John Iannuzzi

MW 09:25 AM MitySOM-AM57X PCB Development: RE: Alternate part for card edge receptacle

There are a couple of options listed here:
https://support.criticallink.com/redmine/projects/mitysom_am57x/wiki/MXM_Connector_Information
I have not checked for stock. Michael Williamson

BS 08:13 AM MitySOM-AM57X PCB Development: Alternate part for card edge receptacle

Hi,
Please suggest any substitutes for "JAE MM70-314B1-2-R300: card edge receptacle" as this part is out of stock in Digikey and Mouser for longer time. Bhima Shankar

10/03/2025

SG 02:17 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Building the MitySOM-5CSX

Hi John,
You're welcome, glad to hear you were able to get u-boot to build. If you continue following our Getting Started Guides for the "Quartus 23.1 project":https://support.criticallink.com/redmine/projects/mityarm-5cs/wiki/Quartus... Seth Graber

JI 11:56 AM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Building the MitySOM-5CSX

Hi Seth,
Thanks, I got u-boot to build. At this point, I have a basic question: If I continue to follow thru the guide for Quartus 23.1, going thru all the steps and build the SD card, what will I have?, i.e. At the end of all this, w... John Iannuzzi

09/22/2025

JI 06:19 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Building the MitySOM-5CSX

Hi Seth,
Thanks. I’ll give it a shot later on.
Best regards,
John John Iannuzzi

SG 05:21 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Building the MitySOM-5CSX

Hi John,
The scripts appears to work fine with python3, below is the output of me running the command manually with python3: Seth Graber

09/21/2025

JI 04:06 PM MitySOM-5CSX Altera Cyclone V FPGA Development: Building the MitySOM-5CSX

Hi,
I have been going thru the build sequence with the makefile and got the following error:
software/preloader/u-boot-socfpga/arch/arm/mach-socfpga/cv_bsp_generator/cv_bsp_generator.py -i hps_isw_handoff/dev_5cs_hps_0 -o software/pr... John Iannuzzi

09/19/2025

JC 02:37 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: RE: AM62A Pinmux Files

Attached to wiki page that is
https://support.criticallink.com/redmine/projects/mitysom_am62x/wiki/Linux_Kernel_Setup_Pinmux#Pinmux-files Jonathan Cormier

09/17/2025

JC 09:50 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: RE: AM62A Pinmux Files

Thanks for bringing this to our attention. I have attached pinmux files for the MitySOM-AM62A. And will check the other 62 families. Jonathan Cormier

TC 01:38 PM MitySOM-AM62, MitySOM-AM62A, & MitySOM-AM62P Software Development: AM62A Pinmux Files

Posting on behalf of a customer ...
> We are just working through setting up a custom image and carrier board.
> ...
> I can't seem to find the Pinmux files for the AM62a, wondering if you know where I could find them? Thomas Catalino