Activity
From 05/23/2020 to 06/21/2020
06/17/2020
- Hello,
I have a MitySom 5csx and I am trying to run the opencl helloworld program described here:
https://support.criticallink.com/redmine/projects/mityarm-5cs/wiki/MitySOM-5CSX_DevKit_OpenCL_BSP,
The version I want to use is ...
06/04/2020
- Hello,
We used to be able to build preloader in Windows 7 environment. However, not any more after we upgraded to Windows 10. Same u-boot package and same build procedures. So we think the OS change might be the course for the failur...
06/03/2020
- JC 06:47 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Worked on this with Zafer. Posting this to tie up the public post.
The solution to this is to pinmux the gpio0_27 pin in the MLO as a gpio.
Note that all the AD pins will be driven as outputs during the ROM bootloader. This can n...
05/28/2020
- JC 05:19 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Zafer Elbi wrote:
> Have you had any chance to create the problem on your side, I mean since the discussion started?
> ...
Sorry, a few fires came up and this got forgotten. We are currently looking to see if we can get the resources ...
05/27/2020
- ZE 07:12 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Have you had any chance to create the problem on your side, I mean since the discussion started?
ZE
From: Elbi, Zafer
Sent: Tuesday, May 26, 2020 4:04 PM
To: 'redmine@criticallink.com' <redmine@criticallink.com>
Subject: RE: [ARM ... - DR 03:33 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- I will do that.
Thank you very much Dan.
Dario - DV 02:33 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- Hi Dario,
You could also try using the "sync" linux command after you copy the rbf over. That should flush anything out to the SD card. I normally do a sync and a reboot after updating the RBF. Seeing as the filesystem is read/write d... - DR 02:15 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- Hi Dan,
Don't worry, I really appreciate your help.
Yes, running “reboot” works and it is the only way to change the FPGA configuration without rebooting the system multiple times. Indeed, even if I change the rbf and then I turn the ... - DV 12:53 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- Hi Dario,
My apologizes for the later reply, it was a long holiday weekend in the states.
So by running "reboot" after copying over the RBF fixed your problem?
Dan
05/26/2020
- ZE 08:05 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Yes, exactly. We did that test before.
It doesn’t show up in 2013, but shows in 2018.
Thanks
From: redmine@criticallink.com <redmine@criticallink.com>
Sent: Tuesday, May 26, 2020 3:36 PM
Subject: [ARM Cortex-A8 Based Products - So... - JC 07:36 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Zafer Elbi wrote:
> Hello,
> ...
Hi Zafer, just to confirm that the 2013.10 u-boot doesn't chatter but the 2018 one does? - ZE 06:47 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Hello,
The last post was about 2 months ago. I am having exactly the same problem.
Our environment uses previous mityARM board (with single DDR2 version).
Before continuing further, I wondered if there has been any progress.
I teste...
05/25/2020
- DR 08:39 AM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- Hi Dan,
thank you very much for helping me with this problem.
Attacched you can find the boot logs for the three cases required.
The checksum verification it is ok by comparing the linux checksum with the PC file. Instead there is no ...