Activity
From 06/01/2018 to 06/30/2018
06/28/2018
I have a custom board with
-- MityDspl-138F module (with FPGA)
-- No Ethernet port
-- UART,USB,SD CARD interface
-- uPP transfer for data process
I have developed a C++ CCS 6.1.3 project with compiler version 7.4.16 which uses ...
06/26/2018
- YY 04:56 AM Software Development: RE: Autoboot Linux in terminal
- It works!
Thanks!
06/25/2018
- JC 01:43 PM Software Development: RE: Autoboot Linux in terminal
- Here you go.
https://stackoverflow.com/questions/10282981/automatic-login-on-angstrom-linux
@# vim /etc/systemd/system/getty.target.wants/serial-getty@ttyS1.service@ - Hello! I have a development board OMAPL138-F, version of kernel linux - 3.2. I have some questions: 1) how can autoboot Linux without entering a user name, 2) what commands are needed and where should they be prescribed?
Thanks! - VP 10:58 AM Software Development: RE: use of IRAM in the project based on MDK_2014-01-13
- Thanks Michael for your tour reply. Actually I am not much familiar with all the settings. To setup my project I followed the link
https://support.criticallink.com/redmine/projects/arm9-platforms/wiki/DSP_Hello_World
and as suggest...
06/22/2018
- MW 06:45 PM Software Development: RE: use of IRAM in the project based on MDK_2014-01-13
- Check the cache settings for the L2 in the BIOS section for the DSP project. The cache can be configured to use up some of the IRAM, you may need to reduce it.
- Hi,
I have a custom board with
-- MityDspl-138F module (with FPGA)
-- No Ethernet port
-- UART,USB,SD CARD interface
-- uPP transfer for data process
We are using MMC card for booting linux and to copy application software files...
06/04/2018
- TR 03:41 PM Software Development: RE: xmlrpc libs for application
- ok, that may be the path of least resistance at this point, thanks for the quick response, Regs, Tom
- JC 03:31 PM Software Development: RE: xmlrpc libs for application
- I'm not sure the opkg-target command works or exists anymore. You could with some effort, install the curl libraries on your l138. Then copy them back to your host machine into the correct sysroot location.
- TR 03:21 PM Software Development: RE: xmlrpc libs for application
- Hi Bob,
So I first took a shot at building xmlrpc with the Angstrom 2012.5 rootfs. Have pulled a version of the code that around the time period and got it configured but it's needs curl. From the target I see that curl is an availabl... - BD 02:19 PM Software Development: RE: xmlrpc libs for application
- Tom Riddle wrote:
> Hi,
> ...
Tom, I'm sorry, but that documentation is out-of-date relative to our latest Yocto-based releases.
If you look at the latest MDK, 2018.04, you see a README with a link to the sources and setup files use... - TR 01:15 PM Software Development: RE: xmlrpc libs for application
- Hi,
Hope someone can assist with the following questions. I need to install some packages on the host build system here and have been following this link as to how.
https://support.criticallink.com/redmine/projects/arm9-platforms/w...
06/02/2018
- TR 01:00 PM Software Development: RE: xmlrpc libs for application
- Hi Jonathan, Thanks for the status. Yea I poked around and couldn't readily find links to sources either. I will take a shot at a few things here 1st. So with the Yocto MDK is it the same kernel version? Regs, Tom
06/01/2018
- JC 05:31 PM Software Development: RE: xmlrpc libs for application
- Tom, the open embedded instructions are unlikely to work. They are at least 6 years out of date and I believe most of the urls required have disappeared.
I updated the wiki page to state this. Let us know if you are interested in bui... - TR 04:51 PM Software Development: RE: xmlrpc libs for application
- Hi Bob, So the link Jonathan posted was helpful with our task of building xmlrpc from source. However I am a bit confused WRT OpenEmbedded Classic, OpenEmbedded core. So the MDK we are using has the Angstrom version below. Which one is t...