Activity
From 08/05/2014 to 09/03/2014
09/02/2014
- JC 08:33 AM Software Development: RE: How to probe the fpga_ctrl & fpga_gpio.ko module
- Have you made any progress with this problem?
08/19/2014
- HK 11:31 AM Software Development: RE: How to probe the fpga_ctrl & fpga_gpio.ko module
yes,
echo "146" > /sys/class/gpio/export --> sh: write error: Invalid argument
it may be that fpga_gpio module is not runing
Thank you.
- JC 08:50 AM Software Development: RE: How to probe the fpga_ctrl & fpga_gpio.ko module
- Did you mean
- HK 08:26 AM Software Development: RE: How to probe the fpga_ctrl & fpga_gpio.ko module
- HYUNG KI KIM wrote:
> I'm tryint to control FPGA of GPIO on the linux driver side with MityL138-DSP(L138-FI-236-RL) mdule.
> ...
- HK 08:24 AM Software Development: RE: How to probe the fpga_ctrl & fpga_gpio.ko module
- HYUNG KI KIM wrote:
> I'm tryint to control FPGA of GPIO on the linux driver side with MityL138-DSP(L138-FI-236-RL) mdule.
> ...
- I'm tryint to control FPGA of GPIO on the linux driver side with MityL138-DSP(L138-FI-236-RL) mdule.
and, loading the myFPGA.bin , fgpa_ctrlko, fpga_gpio.ko module is successfule.
also, test tool of fpgautil is work well.
modprob...
08/18/2014
- AD 04:31 PM PCB Development: RE: Protecting MityDSP module during development
- Hi Udi,
Yes the FPGA I/Os can be damaged by sinking too much current - powered or off. The I/Os have protection diodes to the VCCO and GND rails that can withstand a max of 10mA per pin. Adding series resistors to the I/O pins that ... - We just fried a MityDSP L138F module, and I'm not sure why. I'm suspecting that the problem was that we had an ADC module connected to it (via FPGA) while the L138F module was off. I'm measuring 1.8V on some of the ADC output pins. Cans ...
08/11/2014
- JC 09:21 AM Software Development: RE: DSP HelloWorld Compile with gcc 4.3.3
- tftp stalls when I set the block size larger than the standard MTU size (1500 - overhead = 1468). According to the source the block size is already set to this max value. To accept fragmented packets the source says to enable CONFIG_IP_...
- JC 09:06 AM Software Development: RE: DSP HelloWorld Compile with gcc 4.3.3
- Glad that you got it working. I've never used the block size feature. I'll check out what affect it has on my tftp downloads.
08/08/2014
- DB 03:20 PM Software Development: RE: DSP HelloWorld Compile with gcc 4.3.3
- Successful tftp transfer of mityomap-full.jffs2 from VM to L138 ARM core! Tried setting the blocksize to 4096 in u-boot (U-Boot > setenv tftpblocksize 4096) and entire file transferred, no hangs or system crashes.
After reboot, serial... - JC 12:58 PM Software Development: RE: DSP HelloWorld Compile with gcc 4.3.3
- Occasionally I see timeouts during the transfer but I haven't seen windows or the vm crash during a tftp transfer.
One thing to try would be to setup a link directly between your computer and the device. No need for a cross over cabl... - DB 10:52 AM Software Development: RE: DSP HelloWorld Compile with gcc 4.3.3
- Thank you for the filesystem update procedures. I was able to successfully complete steps 1-5 (writing UBL_SPI_MEM.ais, u-boot-ubl.bin, and uImage to flash NOR).
However, in step 6, after many (>10) attempts to tftp the filesystem (m...
08/07/2014
- JC 08:54 AM Software Development: RE: DSP HelloWorld Compile with gcc 4.3.3
- I created a how to for updating an L138 devkit. Let me know if theres any confusing parts.
[[Updating devkit to latest MDK]]
08/06/2014
- I've recently completed the ARM HelloWorld example via the Starter Guide Wiki page and need help with the DSP HelloWorld example. My set up is as follows:
- MityDSPL138 Industrial I/O board w/ Angstrom GNU/Linux 20107-test-20110516 (...
08/05/2014
- JC 09:30 AM Software Development: RE: How to enable PRU Subsystem on MityDSP-L138F SOM ???
- Patches have been merged into linux-mityarm-v3.2 branch.
- JC 09:16 AM Software Development: RE: I2C 0x8 Address
- Cleaned up and merged changes into mitydsp-linux-v3.2 branch.
http://support.criticallink.com/gitweb/?p=linux-davinci.git;a=commit;h=57c3f55e1dab523b1d26405b11579a6c91a60cc9