Activity
From 09/20/2011 to 10/19/2011
10/19/2011
- MW 12:38 PM Software Development: RE: Using dspQDMA library on OMAP-L138
- Hi Richard,
How are you creating the Semaphore? Zero initialization value?
Is it possible your routine that is pending is running slower than the 5 ms PRD timer (and you are effectively falling behind)? Are your timer routines ru... - I am using the dspQDMA class in a project on the mity-omap processor. I was able to successfully load all of the components and successfully link my project for the dsp. When I execute the dspQDMA->ReadFromFIFO routine (I am reading data...
10/12/2011
- MW 04:01 PM Software Development: RE: HelloWorldDSP.out syntax error
- Hi Peter,
Thank you for your feedback. We'll try to update the Hello World page and address your comments. The challenge of course is that many tools (e.g., CCS from TI and eclipse in general) continue to migrate and change and we m... - PS 03:19 PM Software Development: Reflections after building DSP "Hello, world!"
- I managed to compile the DSP Hello World...*finally*.
(Using Version: 4.2.4.00033 of CCS on WinXP)
I noticed a few of issues when following the guide at:
http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/DSP_Hel... - Hello,
We are trying to debug a uPP application and routed the chan A and Chan B signals through the fpga to connector J104. The Industrial IO data sheet lists 10 of these pins as LVDS pairs and mentions added termination resistors f...
10/10/2011
- MC 03:36 PM Software Development: RE: HelloWorldDSP.out syntax error
- those binaries were a great sanity check for me. you guys might consider posting them to the quick start page.
Mike
10/06/2011
- Hi,
After transferring the jffs2 filesystem via uBoot, using the "nand write.jffs2 C2000000 0 <>" command, is there any method to check whether the file system is fine - before starting kernel - in order to detect block errors or possi...
10/03/2011
- SW 03:48 PM Software Development: RE: uPP digital loopback
- Greg,
I'm using the default ASYNCH3 clock which is PLL_SYSCLK1 I think. This should be divided down automatically. Since I am just using this to test the uPP I won't worry about it and keep the Chan A and Chan B clock divisors equal... - GG 01:49 PM Software Development: RE: uPP digital loopback
- Hi Scott,
As far as I know we have not seen any issue like what you're describing when using a uPP clock driven by the FPGA. Given, we haven't done much work with the uPP in DLB, so it could be a problem unique to that setup.
Anoth... - Hello,
I have a linux driver module to test the uPP in digital loopback. I saw some odd behavior in regards to the clock divisors on Channels A and B. I have the module set to loopback 64 bytes from channel A to channel B. If I se...
09/30/2011
- ME 06:30 AM Software Development: RE: Additional serial port on the MityDSP Profibus dev-kit
- Just thought I'd add a note in case some one else stumbles upon this thread:
Ended up using a Prolific usb-to-serial device that was laying around the office.
I had to build a new kernel with support for usb-to-serial devices and th...
09/29/2011
- Are there test points available on the MityDSP-L138F for the following uPP signals?
'UPP_CHA_ENABLE' = L138 Pin#U16 to FPGA Pin#H5
'UPP_CHA_START' = L138 Pin#W15 to FPGA Pin#C1
'UPP_CHA_CLOCK' = L138 Pin#U17 to FPGA Pin#H7
Than... - SW 10:40 AM Software Development: RE: upp clock
- Greg,
Thanks for the reply. My question was more of how the clocks are setup on the board as a default. I suspected that the clocks were standard with the the uPP xmit clock 300/4 MHz. I found my problem with the uPP code in the en... - ME 08:30 AM Software Development: RE: Additional serial port on the MityDSP Profibus dev-kit
- No, I don't think ssh would work. It has to be something I could open and interact with just like a com port from my code, I'm not sure you can do that with ssh? Either way the recieving end is a windows box and it seems unlikely there w...
- MW 08:18 AM Software Development: RE: Additional serial port on the MityDSP Profibus dev-kit
- (re: comm over ethernet)
Is ssh acceptable? "ssh root@mitydspaddr"
-Mike
- MW 08:17 AM Software Development: RE: Additional serial port on the MityDSP Profibus dev-kit
- The default kernel and root filesystem may "just work". If you plug in the device you should see some messages about it and the device should appear as /dev/ttyUSB0. If that doesn't happen, then you'll need to run make menuconfig and a...
- ME 08:13 AM Software Development: RE: Additional serial port on the MityDSP Profibus dev-kit
- Hmm, I don't really need a physical port. Is there any com over ethernet software availible for these systems?
/ Mattias - ME 08:10 AM Software Development: RE: Additional serial port on the MityDSP Profibus dev-kit
- Thanks for the speedy reply!
One extra port should suffice. I'll order one of the keyspan adapters right away.
I'm using the MityDSP-L138 SoM. Can you point me in the right direction for properly configuring the kernel?
I guess i... - MW 07:49 AM Software Development: RE: Additional serial port on the MityDSP Profibus dev-kit
- Hi Mattias,
I think that your best (or easiest) bet would be to use a usb-to-serial adapter on the Host (USB1) port. If you need more than one, you should be able to use a (powered) hub and attach multiple units. We have used Keyspa... - Hi, I'm wondering what the best way to get an additional serial port is? Is there support for usb-to-serial adapters?
I'm developing something that will need to have both serial, profibus and ethernet support for data transfer and wi...
09/28/2011
- GG 04:35 PM Software Development: RE: upp clock
- Hi Scott,
The fastest you will be able to get the uPP transmit clock to run with your setup is 75 MHz.
From the Upp User's Guide:
"The fixed divisor restricts the maximum speed of the I/O clock to one-fourth the device CPU cloc...
09/27/2011
- I have a userspace upp driver that I am trying to test in loopback mode. I am trying to loopback 1 line of a memory buffer (4096 bytes). I am polling the status register and when it catches the status registers for Q and I appear to ha...
09/23/2011
- We are looking at getting the L138-FI-225-RC that comes with a Spartan 6SLX45. What is the complete FPGA part number that comes on this board?
Thanks,
-Brian
09/21/2011
- SW 05:09 PM Software Development: RE: uPP/DMA registers
- Mike,
I have a couple questions here. I am attempting to write a upp userspace loopback driver/routine. I have memory mapped the pin mux registers, PSC1 registers and the upp registers. I am unsure if the pin mux changes are in eff... - MW 07:51 AM Software Development: RE: Interrupt to ARM side
- Hello Mr. Pailwar,
On the board support package/MDK, in the file sw/ARM/linux/drivers/fpga/fpga_ctrl.c there is some example code of handling interrupts from 2 pins that our framework uses for letting the FPGA interrupt the ARM. We u... - MC 07:29 AM Software Development: RE: HelloWorld dsplink Code composer 5
- Hi Finn
Call me...
/Mads
09/20/2011
- Hello,
I want to generate an interrupt from the FPGA to ARM side of the MityDSP-L138/F board. Is there any example available for doing that and how to make the application aware of the interrupt.
With regards
Pankaj
- MW 10:18 AM FPGA Development: RE: FPGA clock
- On the module itself, the EMA_CLK clock (B7) of the OMAP-L138 is connected to the FPGA. We generally use this clock for most of the core framework we provide. Given the EMIFA must run on this domain, it's convenient and allows us to av...
- Are there any dedicated pins on the FPGA for a clock input? In the IndustrialIO.bin designs do you just use the 100 MHz EMIFA clock as the FPGA input clock? Thanks, Scott