OMAP-L138/AM-1808/AM-1810 initialization passed!
Configuring 128MB mDDR
                      Booting TI User Boot Loader
        UBL Version: 1.65:2.28.1 BuiltJul 11 2011 12:49:53
        UBL Flashtype: SPI
Starting SPI Memory Copy...
Valid magicnum, 0x55424CBB, found at offset 0x00010000.
   DONE
Jumping to entry point at 0xC1080000.


U-Boot 2009.11-00002-gc6adda5 (May 01 2015 - 11:42:37)

I2C:   ready
DRAM:  128 MB
NAND:  256 MiB
MMC:   davinci: 0
In:    serial
Out:   serial
Err:   serial
ARM    Clock : 300000000 Hz
DDR    Clock : 150000000 Hz
EMIFA  CLock : 100000000 Hz
DSP    Clock : 300000000 Hz
ASYNC3 Clock : 150000000 Hz
Enet  config : 2
MMC 0 Enable : 1
Resetting ethernet phy
Net:   No ETH PHY detected!!!

U-Boot > config set
Ethernet Config : 0
UART - 0 Configuration ---
Enable UART : 0
UART - 1 Configuration ---
Enable UART : 1
Baud : 115200
HW Flow Control : 0
Is Console : 1
UART - 2 Configuration ---
Enable UART : 0
SPI - 0 Configuration ---
Enable SPI : 0
SPI - 1 Configuration ---
Enable SPI : 1
CLK is Output : 1
Chip Select [0] Enable : 01
Chip Select [1] Enable : 00
Chip Select [2] Enable : 00
Chip Select [3] Enable : 00
Chip Select [4] Enable : 00
Chip Select [5] Enable : 00
Chip Select [6] Enable : 00
Chip Select [7] Enable : 00
ENA ENable : 0
CLK Rate : 30000000
LCD Configuration
LCD Enable : 0
MMC 0 Configuration
MMC 0 Enable : 1
Write Protect Pin bank : 4
Write Protect Pin bank offset : 1
Card Detect Pin bank : 4
Card Detect Pin bank offset : 0
U-Boot > config save
Configuration Saved
U-Boot > OMAP-L138/AM-1808/AM-1810 initialization passed!
Configuring 128MB mDDR
                      Booting TI User Boot Loader
        UBL Version: 1.65:2.28.1 BuiltJul 11 2011 12:49:53
        UBL Flashtype: SPI
Starting SPI Memory Copy...
Valid magicnum, 0x55424CBB, found at offset 0x00010000.
   DONE
Jumping to entry point at 0xC1080000.


U-Boot 2009.11-00002-gc6adda5 (May 01 2015 - 11:42:37)

I2C:   ready
DRAM:  128 MB
NAND:  256 MiB
MMC:   davinci: 0
In:    serial
Out:   serial
Err:   serial
ARM    Clock : 300000000 Hz
DDR    Clock : 150000000 Hz
EMIFA  CLock : 100000000 Hz
DSP    Clock : 300000000 Hz
ASYNC3 Clock : 150000000 Hz
Enet  config : 2
MMC 0 Enable : 1
Resetting ethernet phy
Net:   No ETH PHY detected!!!

U-Boot > mmcinfo
Device: davinci
Manufacturer ID: 3
OEM: 5344
Name: SD04G
Tran Speed: 25000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3965190144
Bus Width: 4-bit
U-Boot > setenv bootargs mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/mmcblk0p1 rw rootwait ip=off
U-Boot > ext2load mmc 0:1 c0700000 /boot/uImage
Loading file "/boot/uImage" from mmc device 0:1 (xxa1)
2530232 bytes read
U-Boot > bootm
## Booting kernel from Legacy Image at c0700000 ...
   Image Name:   Linux-3.2.0
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2530168 Bytes =  2.4 MB
   Load Address: c0008000
   Entry Point:  c0008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.2.0 (root@mitydsp) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #1 PREEMPT Mon Jan 13 11:06:16 EST 2014
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: MityDSP-L138/MityARM-1808
Ignoring unrecognised tag 0x42000101
Memory policy: ECC disabled, Data cache writethrough
DaVinci da850/omap-l138/am18x variant 0x1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 24384
Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/mmcblk0p1 rw rootwait ip=off
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 96MB = 96MB total
Memory: 91368k/91368k available, 6936k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xc6800000 - 0xfea00000   ( 898 MB)
    lowmem  : 0xc0000000 - 0xc6000000   (  96 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc052c598   (5266 kB)
      .init : 0xc052d000 - 0xc0555000   ( 160 kB)
      .data : 0xc0556000 - 0xc05b5a80   ( 383 kB)
       .bss : 0xc05b5aa4 - 0xc05e2490   ( 179 kB)
NR_IRQS:245
Console: colour dummy device 80x30
Calibrating delay loop... 148.88 BogoMIPS (lpj=744448)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
DaVinci: 144 gpio irqs
print_constraints: dummy:
NET: Registered protocol family 16
baseboard_pre_init: Entered
mityomapl138_setup_nand: using 8 bit data
baseboard_init [IndustrialIO]...
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV
print_constraints: VDCDC2: 1800 mV
print_constraints: VDCDC3: 1200 mV
print_constraints: LDO1: 1800 mV
print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV
Advanced Linux Sound Architecture Driver Version 1.0.24.
Switching to clocksource timer0_1
musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
Waiting for USB PHY clock good...
musb-hdrc musb-hdrc: USB OTG mode controller at fee00000 using PIO, IRQ 58
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 178
io scheduler noop registered (default)
start plist test
end plist test
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A
serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A
console [ttyS1] enabled
serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A
brd: module loaded
at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
MityOMAPL138: Found MAC = 40:d8:55:17:c8:1c
MityOMAPL138: Part Number = L138-FG-225-RC
ahci ahci: forcing PORTS_IMPL to 0x1
ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
Creating 2 MTD partitions on "davinci_nand.1":
0x000000000000-0x000008000000 : "rootfs"
0x000008000000-0x000010000000 : "homefs"
davinci_nand davinci_nand.1: controller rev. 2.5
spi_davinci spi_davinci.1: DMA: supported
spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0
m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes)
Creating 8 MTD partitions on "m25p80":
0x000000000000-0x000000010000 : "ubl"
0x000000010000-0x000000090000 : "u-boot"
0x000000090000-0x0000000a0000 : "u-boot-env"
0x0000000a0000-0x0000000b0000 : "periph-config"
No LCD configured
MII PHY configured
0x0000000b0000-0x000000100000 : "reserved"
0x000000100000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "fpga"
0x000000600000-0x000000800000 : "spare"
spi_davinci spi_davinci.1: Controller at 0xfef0e000
CAN device driver interface
ata1: SATA link down (SStatus 0 SControl 300)
mcp251x spi1.1: MCP251x didn't enter in conf mode after reset
mcp251x spi1.1: Probe failed
mcp251x spi1.1: probe failed
davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
davinci_mdio davinci_mdio.0: no live phy, scanning all
davinci_mdio: probe of davinci_mdio.0 failed with error -5
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci ohci.0: DA8xx OHCI
ohci ohci.0: new USB bus registered, assigned bus number 1
Waiting for USB PHY clock good...
ohci ohci.0: irq 59, io mem 0x01e25000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
omap_rtc: RTC power up reset detected
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
mmc0: new SDHC card at address 8eeb
mmcblk0: mmc0:8eeb SD04G 3.69 GiB
 mmcblk0: p1
dsd1791 spi1.2: Failed to add route LLOUT->Line Out
asoc: dsd1791 <-> davinci-mcasp.0 mapping ok
ALSA device list:
  #0: MityDSP-L138 INDIO
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
regulator_init_complete: LDO2: incomplete constraints, leaving on
regulator_init_complete: LDO1: incomplete constraints, leaving on
regulator_init_complete: VDCDC3: incomplete constraints, leaving on
regulator_init_complete: VDCDC2: incomplete constraints, leaving on
regulator_init_complete: VDCDC1: incomplete constraints, leaving on
console [netcon0] enabled
netconsole: network logging started
omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p1): using internal journal
EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 179:1.
devtmpfs: mounted
Freeing init memory: 160K
Failed to mount /sys/kernel/security: No such file or directory

Welcome to The Ångström Distribution!

NET: Registered protocol family 10
Starting LSB: The RPC portmapper...
Starting udev Coldplug all Devices...
Starting Remount API VFS...
Starting Temporary Directory...
Starting Journal Service...
Started Journal Service                                                [  OK  ]
Starting POSIX Message Queue File System...
Starting Apply Kernel Variables...
Starting Debug File System...
Started Set Up Additional Binary Formats                               [  OK  ]
Started Huge Pages File System                                         [  OK  ]
Starting Load Kernel Modules...
Starting File System Check on Root Device...
Starting udev Kernel Device Manager...
Started LSB: The RPC portmapper                                        [  OK  ]
Started Remount API VFS                                                [  OK  ]
Started Temporary Directory                                            [  OK  ]
Started POSIX Message Queue File System                                [  OK  ]
Started Apply Kernel Variables                                         [  OK  ]
Started Debug File System                                              [  OK  ]
udevd[1097]: starting version 182
Started File System Check on Root Device                               [  OK  ]
Started udev Kernel Device Manager                                     [  OK  ]
Started Load Kernel Modules                                            [  OK  ]
Started Configuration File System                                      [  OK  ]
Started FUSE Control File System                                       [  OK  ]
Starting Remount Root FS...
Started Remount Root FS                                                [  OK  ]
Started Machine ID first boot configure                                [  OK  ]
Starting Load Random Seed...
Starting Recreate Volatile Files and Directories...
Started Run pending postinsts                                          [  OK  ]
Started Load Random Seed                                               [  OK  ]
Started Recreate Volatile Files and Directories                        [  OK  ]
Starting Restore Sound Card State...
Starting Timestamping service...
Started Timestamping service                                           [  OK  ]
Started SSH Key Generation                                             [  OK  ]
Starting Permit User Sessions...
portmap[1077]: Starting portmap daemon...
Started Permit User Sessions                                           [  OK  ]
Started Restore Sound Card State                                       [  OK  ]
Starting Serial Getty on ttyS1...
Started Serial Getty on ttyS1                                          [  OK  ]

.---O---.
|       |                  .-.           o o
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution mityomapl138 ttyS1

Angstrom v2012.05 - Kernel 3.2.0

mityomapl138 login: Started udev Coldplug all Devices                                      [  OK  ]
Starting Networking...
PHY 0:03 not found
net eth0: could not connect to phy 0:03
ADDRCONF(NETDEV_UP): eth0: link is not ready
Started Networking                                                     [  OK  ]
Starting DropBear SSH Server...
Started DropBear SSH Server                                            [  OK  ]
Starting Getty on tty1...
Started Getty on tty1                                                  [  OK  ]

.---O---.
|       |                  .-.           o o
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution mityomapl138 ttyS1

Angstrom v2012.05 - Kernel 3.2.0

mityomapl138 login: root
Last login: Sat Jan  1 00:12:53 UTC 2000 on ttyS1
root@mityomapl138:~# mount
rootfs on / type rootfs (rw)
/dev/root on / type ext3 (rw,relatime,errors=continue,user_xattr,barrier=1,data=writeback)
devtmpfs on /dev type devtmpfs (rw,relatime,size=45684k,nr_inodes=11421,mode=755)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620)
tmpfs on /run type tmpfs (rw,nosuid,nodev,relatime,mode=755)
tmpfs on /sys/fs/cgroup type tmpfs (rw,nosuid,nodev,noexec,relatime,mode=755)
cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,release_agent=/lib/systemd/systemd-cgroups-agent,name=systemd)
tmpfs on /tmp type tmpfs (rw,relatime)
mqueue on /dev/mqueue type mqueue (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
/dev/mmcblk0p1 on /media/mmcblk0p1 type ext3 (rw,relatime,errors=continue,user_xattr,barrier=1,data=writeback)
root@mityomapl138:~# cp /media/mmcblk0p1/home/root/TestuPPLBARM /tmp/
root@mityomapl138:~# cp /media/mmcblk0p1/home/root/TestuPPLBDSP.out /tmp/
root@mityomapl138:~# insmod /lib/modules/$(uname -r)/extra/dsplinkk.ko
Disabling lock debugging due to kernel taint
DSPLINK Module (1.65.00.03) created on Date: Jan 13 2014 Time: 16:10:29
root@mityomapl138:~# ./TestuPPLBARM TestuPPLBDSP.out
can't set spi mode: Bad file descriptor
Aborted
root@mityomapl138:~# ./TestuPPLBARM TestuPPLBDSP.out
can't set spi mode: Bad file descriptor
Aborted
root@mityomapl138:~#
