
U-Boot SPL 2013.01.01 (Apr 08 2015 - 15:41:35)
BOARD : Critical Link MitySOM-5CSx Module
CLOCK: EOSC1 clock 25000 KHz
CLOCK: EOSC2 clock 25000 KHz
CLOCK: F2S_SDR_REF clock 0 KHz
CLOCK: F2S_PER_REF clock 0 KHz
CLOCK: MPU clock 925 MHz
CLOCK: DDR clock 400 MHz
CLOCK: UART clock 100000 KHz
CLOCK: MMC clock 50000 KHz
CLOCK: QSPI clock 370000 KHz
RESET: COLD
INFO : Watchdog enabled
SDRAM: Initializing MMR registers
SDRAM: Calibrating PHY
SEQ.C: Preparing to start memory calibration
SEQ.C: CALIBRATION PASSED
SDRAM: 1024 MiB
SDRAM: Scrubbing 0x01000000 - 0x02000000
SDRAM: Scrubbing success with 25 ms
SDRAM: Scrubbing 0x00000000 - 0x01000000
SDRAM: Scrubbing 0x02000000 - 0x40000000
SDRAM: ECC Enabled
ALTERA DWMMC: 0
SDRAM: Scrubbing success with consuming additional 1505 ms


U-Boot 2013.01.01 (Apr 08 2015 - 15:42:36) Critical Link MitySOM-5CSx

CPU   : Altera SOCFPGA Platform
BOARD : Critical Link MitySOM-5CSx Module
I2C:   ready
DRAM:  1 GiB
MMC:   ALTERA DWMMC: 0
In:    serial
Out:   serial
Err:   serial
Net:   mii0

preboot reading MMC uBoot ENV data

** File not found /etc/uBootStatic.env **
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
ERROR: Environment import failed: errno = 12

at cmd_nvedit.c:1004/do_env_import()
** File not found /etc/uBoot.env **
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
ERROR: Environment import failed: errno = 12

at cmd_nvedit.c:1004/do_env_import()
...done
Hit any key to stop autoboot:  0
gpio: pin 28 (bank/mask = 0/0x10000000)
gpio: pin 28 (gpio 28) value is 0
gpio: pin 28 (bank/mask = 0/0x10000000)
gpio: pin 28 (gpio 28) value is 1
gpio: pin 0 (bank/mask = 0/0x00000001)
gpio: pin 0 (gpio 0) value is 1
gpio: pin 9 (bank/mask = 0/0x00000200)
gpio: pin 9 (gpio 9) value is 0
gpio: pin 9 (bank/mask = 0/0x00000200)
gpio: pin 9 (gpio 9) value is 1
7007184 bytes read in 390 ms (17.1 MiB/s)
## Starting application at 0x3FF78704 ...
## Application terminated, rc = 0x0
3663536 bytes read in 264 ms (13.2 MiB/s)
20209 bytes read in 56 ms (351.6 KiB/s)
## Booting kernel from Legacy Image at 00007fc0 ...
   Image Name:   Linux-3.16.0-g1d15155
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3663472 Bytes = 3.5 MiB
   Load Address: 00008000
   Entry Point:  00008000
## Flattened Device Tree blob at 00000100
   Booting using the fdt blob at 0x00000100
   XIP Kernel Image ... OK
OK
   Loading Device Tree to 03ff8000, end 03fffef0 ... OK

Starting kernel ...

Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Linux version 3.16.0-g1d15155 (user@MitySOM-Dev) (gcc version 4.8.1 (GCC) ) #1 SMP Thu Apr 2 10:24:03 BST 2015
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: MitySOM-5CSX Altera SOCFPGA Cyclone V
Memory policy: Data cache writealloc
PERCPU: Embedded 8 pages/cpu @9fbd5000 s11008 r8192 d13568 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait mem=512M
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511736K/524288K available (5516K kernel code, 277K rwdata, 1540K rodata, 382K init, 125K bss, 12552K reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
    vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
    lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x806ec300   (7057 kB)
      .init : 0x806ed000 - 0x8074cb00   ( 383 kB)
      .data : 0x8074e000 - 0x807937e8   ( 278 kB)
       .bss : 0x807937e8 - 0x807b2e1c   ( 126 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L2C: platform modifies aux control register: 0x02060000 -> 0x32460000
L2C: platform provided aux values permit register corruption.
L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32460000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410030c9, AUX_CTRL 0x76460001
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949672950ns
Console: colour dummy device 80x30
Calibrating delay loop... 1836.64 BogoMIPS (lpj=9183232)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
ftrace: allocating 18739 entries in 55 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x4fa588 - 0x4fa5e0
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated.
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
NET: Registered protocol family 16
fpga bridge driver
DMA: preallocated 256 KiB pool for atomic coherent allocations
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
altera_hps2fpga_bridge soc:fpgabridge@0: fpga bridge [hps2fpga] registered as device hps2fpga
altera_hps2fpga_bridge soc:fpgabridge@0: init-val not specified
altera_hps2fpga_bridge soc:fpgabridge@1: fpga bridge [lshps2fpga] registered as device lwhps2fpga
altera_hps2fpga_bridge soc:fpgabridge@1: init-val not specified
altera_hps2fpga_bridge soc:fpgabridge@2: fpga bridge [fpga2hps] registered as device fpga2hps
altera_hps2fpga_bridge soc:fpgabridge@2: init-val not specified
FPGA Mangager framework driver
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
Switched to clocksource timer1
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
arm-pmu arm-pmu: PMU:CTI successfully enabled for 2 cores
futex hash table entries: 512 (order: 3, 32768 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
ntfs: driver 2.1.30 [Flags: R/W].
jffs2: version 2.2. (NAND)  2001-2006 Red Hat, Inc.
msgmni has been set to 999
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
console [ttyS0] disabled
ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194, base_baud = 6250000) is a 16550A
console [ttyS0] enabled
ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 195, base_baud = 6250000) is a 16550A
altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0
brd: module loaded
at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write
CAN device driver interface
/soc/ethernet@ff702000: could not get #reset-cells for /soc/rstmgr@ffd05000
stmmaceth ff702000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
 Ring mode enabled
 DMA HW capability register supported
 Enhanced/Alternate descriptors
        Enabled extended descriptors
 RX Checksum Offload Engine supported (type 2)
 TX Checksum insertion supported
 Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: No PHY found
stmmac_pltfr_probe: main driver probe failed
dwc2 ffb40000.usb: s3c_hsotg_corereset: reset failed, GRSTCTL=00000000
dwc2 ffb40000.usb: EPs: 0, shared fifos, 0 entries in SPRAM
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at drivers/usb/dwc2/gadget.c:203 s3c_hsotg_init_fifo+0x1b8/0x1ec()
insufficient fifo memory
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.16.0-g1d15155 #1
[<8001860c>] (unwind_backtrace) from [<80013260>] (show_stack+0x20/0x24)
[<80013260>] (show_stack) from [<804f4ef4>] (dump_stack+0x8c/0x9c)
[<804f4ef4>] (dump_stack) from [<800264fc>] (warn_slowpath_common+0x80/0x9c)
[<800264fc>] (warn_slowpath_common) from [<80026558>] (warn_slowpath_fmt+0x40/0x48)
[<80026558>] (warn_slowpath_fmt) from [<803a72dc>] (s3c_hsotg_init_fifo+0x1b8/0x1ec)
[<803a72dc>] (s3c_hsotg_init_fifo) from [<803aa50c>] (dwc2_gadget_init+0x1ec/0x6a4)
[<803aa50c>] (dwc2_gadget_init) from [<803aad5c>] (dwc2_driver_probe+0x100/0x174)
[<803aad5c>] (dwc2_driver_probe) from [<8032432c>] (platform_drv_probe+0x28/0x58)
[<8032432c>] (platform_drv_probe) from [<803224fc>] (really_probe+0x84/0x224)
[<803224fc>] (really_probe) from [<803227a8>] (__driver_attach+0xa8/0xac)
[<803227a8>] (__driver_attach) from [<803208b0>] (bus_for_each_dev+0x70/0xa4)
[<803208b0>] (bus_for_each_dev) from [<80322080>] (driver_attach+0x2c/0x30)
[<80322080>] (driver_attach) from [<80321cf8>] (bus_add_driver+0x15c/0x204)
[<80321cf8>] (bus_add_driver) from [<80323018>] (driver_register+0x88/0x108)
[<80323018>] (driver_register) from [<803242fc>] (__platform_driver_register+0x64/0x6c)
[<803242fc>] (__platform_driver_register) from [<807183dc>] (dwc2_platform_driver_init+0x1c/0x20)
[<807183dc>] (dwc2_platform_driver_init) from [<80008940>] (do_one_initcall+0x9c/0x1dc)
[<80008940>] (do_one_initcall) from [<806edde4>] (kernel_init_freeable+0x1e0/0x280)
[<806edde4>] (kernel_init_freeable) from [<804f0ce8>] (kernel_init+0x1c/0x100)
[<804f0ce8>] (kernel_init) from [<8000ebf8>] (ret_from_fork+0x14/0x20)
---[ end trace 38a0734e9bd7cabb ]---
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at drivers/usb/dwc2/gadget.c:214 s3c_hsotg_init_fifo+0x1e4/0x1ec()
insufficient fifo memory
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G        W     3.16.0-g1d15155 #1
[<8001860c>] (unwind_backtrace) from [<80013260>] (show_stack+0x20/0x24)
[<80013260>] (show_stack) from [<804f4ef4>] (dump_stack+0x8c/0x9c)
[<804f4ef4>] (dump_stack) from [<800264fc>] (warn_slowpath_common+0x80/0x9c)
[<800264fc>] (warn_slowpath_common) from [<80026558>] (warn_slowpath_fmt+0x40/0x48)
[<80026558>] (warn_slowpath_fmt) from [<803a7308>] (s3c_hsotg_init_fifo+0x1e4/0x1ec)
[<803a7308>] (s3c_hsotg_init_fifo) from [<803aa50c>] (dwc2_gadget_init+0x1ec/0x6a4)
[<803aa50c>] (dwc2_gadget_init) from [<803aad5c>] (dwc2_driver_probe+0x100/0x174)
[<803aad5c>] (dwc2_driver_probe) from [<8032432c>] (platform_drv_probe+0x28/0x58)
[<8032432c>] (platform_drv_probe) from [<803224fc>] (really_probe+0x84/0x224)
[<803224fc>] (really_probe) from [<803227a8>] (__driver_attach+0xa8/0xac)
[<803227a8>] (__driver_attach) from [<803208b0>] (bus_for_each_dev+0x70/0xa4)
[<803208b0>] (bus_for_each_dev) from [<80322080>] (driver_attach+0x2c/0x30)
[<80322080>] (driver_attach) from [<80321cf8>] (bus_add_driver+0x15c/0x204)
[<80321cf8>] (bus_add_driver) from [<80323018>] (driver_register+0x88/0x108)
[<80323018>] (driver_register) from [<803242fc>] (__platform_driver_register+0x64/0x6c)
[<803242fc>] (__platform_driver_register) from [<807183dc>] (dwc2_platform_driver_init+0x1c/0x20)
[<807183dc>] (dwc2_platform_driver_init) from [<80008940>] (do_one_initcall+0x9c/0x1dc)
[<80008940>] (do_one_initcall) from [<806edde4>] (kernel_init_freeable+0x1e0/0x280)
[<806edde4>] (kernel_init_freeable) from [<804f0ce8>] (kernel_init+0x1c/0x100)
[<804f0ce8>] (kernel_init) from [<8000ebf8>] (ret_from_fork+0x14/0x20)
---[ end trace 38a0734e9bd7cabc ]---
dwc2 ffb40000.usb: wrong number of EPs (zero)
dwc2: probe of ffb40000.usb failed with error -22
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
rtc-ab18xx 0-0069: rtc core: registered ab1803 as rtc0
rtc-ab18xx 0-0069: 192 bytes nvram
i2c /dev entries driver
i2c_designware ffc05000.i2c: controller timed out
i2c_designware ffc05000.i2c: controller timed out
i2c_designware ffc05000.i2c: controller timed out
i2c_designware ffc05000.i2c: controller timed out
i2c_designware ffc05000.i2c: controller timed out
i2c_designware ffc05000.i2c: controller timed out
Synopsys Designware Multimedia Card Interface Driver
dw_mmc ff704000.dwmmc0: no vmmc regulator found: -19
dw_mmc ff704000.dwmmc0: Using internal DMA controller.
dw_mmc ff704000.dwmmc0: Version ID is 240a
dw_mmc ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo
dw_mmc ff704000.dwmmc0: 1 slots initialized
lp5562 0-0030: internal clock used
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using arm/armv7-ca9
TCP: cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
ThumbEE CPU extension supported.
Registering SWP/SWPB emulation handler
Waiting for root device /dev/mmcblk0p2...
mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 50000000Hz, actual 50000000HZ div = 2)
mmc0: new high speed SDHC card at address 1234
mmcblk0: mmc0:1234 SA04G 3.63 GiB
 mmcblk0: p1 p2 p3
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 380K (806ed000 - 8074c000)
INIT: version 2.88 booting
Error opening /dev/fb0: No such file or directory
Starting udev
udevd[70]: starting version 182
input: gpio_keys as /devices/gpio_keys/input/input0
random: nonblocking pool is initialized
Starting Bootlog daemon: bootlogd.
Populating dev cache
Configuring network interfaces... eth0: ERROR while getting interface flags: No such device
Starting rpcbind daemon...NET: Registered protocol family 10
done.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Fri Apr 10 09:34:00 UTC 2015
Starting atd: OK
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd
  generating ssh RSA key...
  generating ssh ECDSA key...
  generating ssh DSA key...
done.
creating NFS state directory: done
NFS daemon support not enabled in kernel
Starting system log daemon...0
Starting kernel log daemon...0
Starting Lighttpd Web Server: lighttpd.
Starting crond: OK
Starting Network Interface Plugging Daemon: eth0.
Stopping Bootlog daemon: bootlogd.

Poky (Yocto Project Reference Distro) 1.5.4 mitysom-5csx /dev/ttyS0

mitysom-5csx login: root
root@mitysom-5csx:~# ifconfig
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@mitysom-5csx:~#
