Mity CPU Platforms » MitySOM-QC6490

&soc {

qcom,cam-res-mgr {

compatible = "qcom,cam-res-mgr";

status = "ok";

gpios-shared-pinctrl = <640>;

shared-pctrl-gpio-names = "gmsl";

pinctrl-names = "gmsl_active", "gmsl_suspend";

pinctrl-0 = <&cam_sensor_active_gmsl>;

pinctrl-1 = <&cam_sensor_suspend_gmsl>;

};

};

&tlmm {

cam_sensor_active_rst5: cam_sensor_active_rst5 {

/* RESET 5 */

mux {

pins = "gpio115";

function = "gpio";

};

config {

pins = "gpio115";

bias-disable; /* No PULL */

drive-strength = <2>; /* 2 MA */

};

};

cam_sensor_suspend_rst5: cam_sensor_suspend_rst5 {

/* RESET 5 */

mux {

pins = "gpio115";

function = "gpio";

};

config {

pins = "gpio115";

bias-pull-down; /* PULL DOWN */

drive-strength = <2>; /* 2 MA */

output-low;

};

};

cam_sensor_active_gmsl: cam_sensor_active_gmsl {

/* GMSL_ENABLE */

mux {

pins = "gpio93";

function = "gpio";

};

config {

pins = "gpio93";

bias-pull-up;

drive-strength = <2>; /* 2 MA */

output-high;

};

};

cam_sensor_suspend_gmsl: cam_sensor_suspend_gmsl {

/* GMSL_ENABLE */

mux {

pins = "gpio93";

function = "gpio";

};

config {

pins = "gpio93";

bias-pull-down; /* PULL DOWN */

drive-strength = <2>; /* 2 MA */

output-low;

};

};

};

/*cam0-ov9282*/

qcom,cam-sensor1 {

cell-index = <1>;

sensor-position-roll = <0>;

sensor-position-pitch = <0>;

sensor-position-yaw = <180>;

cam_vio-supply = <&vreg_l18b_1p8>;

regulator-names = "cam_vio";

power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;

rgltr-cntrl-support;

pwm-switch;

rgltr-min-voltage = <1800000>;

rgltr-max-voltage = <1800000>;

rgltr-load-current = <120000>;

gpio-no-mux = <0>;

pinctrl-names = "cam_default", "cam_suspend";

pinctrl-0 = <&cam_sensor_mclk0_active>;

pinctrl-1 = <&cam_sensor_mclk0_suspend>;

/*cam0b-ov9282*/

qcom,cam-sensor7 {

cell-index = <7>;

compatible = "qcom,cam-sensor";

csiphy-sd-index = <1>;

sensor-position-roll = <0>;

sensor-position-pitch = <0>;

sensor-position-yaw = <180>;

cam_vio-supply = <&vreg_l18b_1p8>;

regulator-names = "cam_vio";

power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;

rgltr-cntrl-support;

pwm-switch;

rgltr-min-voltage = <1800000>;

rgltr-max-voltage = <1800000>;

rgltr-load-current = <120000>;

gpio-no-mux = <0>;

pinctrl-names = "cam_default", "cam_suspend";

pinctrl-0 = <&cam_sensor_mclk1_active>;

pinctrl-1 = <&cam_sensor_mclk1_suspend>;

gpios = <&tlmm 65 0>;

gpio-req-tbl-num = <0>;

gpio-req-tbl-flags = <0>;

gpio-req-tbl-label = "CAM_EN1";

sensor-mode = <0>;

cci-master = <1>;

status = "ok";

clocks = <&camcc CAM_CC_MCLK1_CLK>;

clock-names = "cam_clk";

clock-cntl-level = "nominal";

clock-rates = <24000000>;

};

};

&cam_cci1 {

/*cam1-ov9282*/

qcom,cam-sensor6 {

cell-index = <6>;

compatible = "qcom,cam-sensor";

csiphy-sd-index = <2>;

sensor-position-roll = <0>;

sensor-position-pitch = <0>;

sensor-position-yaw = <180>;

cam_vio-supply = <&vreg_l18b_1p8>;

regulator-names = "cam_vio";

power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;

rgltr-cntrl-support;

pwm-switch;

rgltr-min-voltage = <1800000>;

rgltr-max-voltage = <1800000>;

rgltr-load-current = <120000>;

gpio-no-mux = <0>;

pinctrl-names = "cam_default", "cam_suspend";

pinctrl-0 = <&cam_sensor_mclk2_active>;

pinctrl-1 = <&cam_sensor_mclk2_suspend>;

gpios = <&tlmm 66 0>;

gpio-req-tbl-num = <0>;

gpio-req-tbl-flags = <0>;

gpio-req-tbl-label = "CAMIF_MCLK2";

sensor-mode = <0>;

cci-master = <0>;

status = "ok";

clocks = <&camcc CAM_CC_MCLK2_CLK>;

clock-names = "cam_clk";

clock-cntl-level = "nominal";

clock-rates = <24000000>;

};

/*cam2-ov9282*/

qcom,cam-sensor5 {

cell-index = <5>;

compatible = "qcom,cam-sensor";

csiphy-sd-index = <3>;

sensor-position-roll = <0>;

sensor-position-pitch = <0>;

sensor-position-yaw = <180>;

cam_vio-supply = <&vreg_l18b_1p8>;

regulator-names = "cam_vio";

power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;

rgltr-cntrl-support;

pwm-switch;

rgltr-min-voltage = <1800000>;

rgltr-max-voltage = <1800000>;

rgltr-load-current = <120000>;

gpio-no-mux = <0>;

pinctrl-names = "cam_default", "cam_suspend";

pinctrl-0 = <&cam_sensor_mclk3_active

&cam_sensor_active_rst3>;

pinctrl-1 = <&cam_sensor_mclk3_suspend

&cam_sensor_suspend_rst3>;

gpios = <&tlmm 67 0>,

<&tlmm 78 0>;

gpio-reset = <1>;

gpio-req-tbl-num = <0 1>;

gpio-req-tbl-flags = <1 0>;

gpio-req-tbl-label = "CAMIF_MCLK3",

"CAM_RESET3";

sensor-mode = <0>;

cci-master = <1>;

status = "ok";

clocks = <&camcc CAM_CC_MCLK3_CLK>;

clock-names = "cam_clk";

clock-cntl-level = "nominal";

clock-rates = <24000000>;

};

/*cam4-ov9282*/

qcom,cam-sensor4 {

cell-index = <4>;

compatible = "qcom,cam-sensor";

csiphy-sd-index = <4>;

sensor-position-roll = <0>;

sensor-position-pitch = <0>;

sensor-position-yaw = <180>;

cam_vio-supply = <&vreg_l18b_1p8>;

regulator-names = "cam_vio";

power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;

rgltr-cntrl-support;

pwm-switch;

rgltr-min-voltage = <1800000>;

rgltr-max-voltage = <1800000>;

rgltr-load-current = <120000>;

gpio-no-mux = <0>;

pinctrl-names = "cam_default", "cam_suspend";

pinctrl-0 = <&cam_sensor_mclk4_active>;

pinctrl-1 = <&cam_sensor_mclk4_suspend>;

gpios = <&tlmm 68 0>;

gpio-req-tbl-num = <0>;

gpio-req-tbl-flags = <0>;

gpio-req-tbl-label = "CAMIF_MCLK4";

sensor-mode = <0>;

cci-master = <1>;

status = "ok";

clocks = <&camcc CAM_CC_MCLK4_CLK>;

clock-names = "cam_clk";

clock-cntl-level = "nominal";

clock-rates = <24000000>;

};

/*cam3-imx577*/

// rb3_slot3: qcom,cam-sensor0 {

// cell-index = <0>;

// compatible = "qcom,cam-sensor";

// csiphy-sd-index = <3>;

// sensor-position-roll = <0>;

// sensor-position-pitch = <0>;

// sensor-position-yaw = <180>;

// eeprom-src = <&eeprom_cam3>;

// cam_vio-supply = <&vreg_l18b_1p8>;

// regulator-names = "cam_vio";

// power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;

// rgltr-cntrl-support;

// pwm-switch;

// rgltr-min-voltage = <1800000>;

// rgltr-max-voltage = <1800000>;

// rgltr-load-current = <120000>;

// gpio-no-mux = <0>;

// pinctrl-names = "cam_default", "cam_suspend";

// pinctrl-0 = <&cam_sensor_mclk3_active>;

// pinctrl-1 = <&cam_sensor_mclk3_suspend>;

// gpios = <&tlmm 67 0>;

// gpio-reset = <1>;

// gpio-req-tbl-num = <0 1>;

// gpio-req-tbl-flags = <1 0>;

// gpio-req-tbl-label = "CAMIF_MCLK3";

// sensor-mode = <0>;

// cci-master = <1>;

// status = "ok";

// clocks = <&camcc CAM_CC_MCLK3_CLK>;

// clock-names = "cam_clk";

// clock-cntl-level = "nominal";

// clock-rates = <24000000>;

// };

// eeprom_cam3: qcom,eeprom3 {

// cell-index = <0>;

// compatible = "qcom,eeprom";

// cam_vio-supply = <&vreg_l18b_1p8>;

// regulator-names = "cam_vio";

// power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;

// rgltr-cntrl-support;

// rgltr-min-voltage = <1800000>;

// rgltr-max-voltage = <1800000>;

// rgltr-load-current = <120000>;

// gpio-no-mux = <0>;

// pinctrl-names = "cam_default", "cam_suspend";

// pinctrl-0 = <&cam_sensor_mclk3_active

// &cam_sensor_active_rst3>;

// pinctrl-1 = <&cam_sensor_mclk3_suspend

// &cam_sensor_suspend_rst3>;

// gpios = <&tlmm 67 0>,

// <&tlmm 78 0>;

// gpio-reset = <1>;

// gpio-req-tbl-num = <0 1>;

// gpio-req-tbl-flags = <1 0>;

// gpio-req-tbl-label = "CAMIF_MCLK3",

// "CAM_RESET3";

// sensor-position = <1>;

// sensor-mode = <0>;

// cci-master = <1>;

// qcom,cam-power-seq-type ="cam_reset","cam_vio","cam_clk","cam_reset";

// qcom,cam-power-seq-val = "cam_reset","cam_vio"

// ,"cam_mclk","cam_reset";

// qcom,cam-power-seq-cfg-val = <0 1 24000000 1>;

// qcom,cam-power-seq-delay = <1 0 1 18>;

// status = "ok";

// clocks = <&camcc CAM_CC_MCLK3_CLK>;

// clock-names = "cam_clk";

// clock-cntl-level = "nominal";

// clock-rates = <24000000>;

// };