Project

General

Profile

RE: Enable DDR ECC in Am62A processor » am62a_ecc_bootlog.txt

Jonathan Cormier, 05/14/2025 08:34 PM

 
1
U-Boot SPL 2024.04-00103-g2db3e4171389-dirty (May 14 2025 - 16:07:55 -0400)
2
SYSFW ABI: 4.0 (firmware rev 0x000a '10.1.8--v10.01.08 (Fiery Fox)')
3
Configuring LPDDR4 for 4GB
4
ECC is enabled, priming DDR which will take several seconds.
5
ECC: priming DDR completed in 2035 msec
6
SPL initial stack usage: 17072 bytes
7
Trying to boot from MMC2
8
Authentication passed
9
Authentication passed
10
Authentication passed
11
Authentication passed
12
Authentication passed
13
Starting ATF on ARM64 core...
14

    
15
NOTICE:  BL31: v2.11.0(release):v2.11.0-906-g58b25570c9-dirty
16
NOTICE:  BL31: Built : 04:20:32, Nov  1 2024
17

    
18
U-Boot SPL 2024.04-00103-g2db3e4171389-dirty (May 14 2025 - 16:08:02 -0400)
19
SYSFW ABI: 4.0 (firmware rev 0x000a '10.1.8--v10.01.08 (Fiery Fox)')
20
Trying to boot from MMC2
21
Authentication passed
22
Authentication passed
23

    
24

    
25
U-Boot 2024.04-00103-g2db3e4171389-dirty (May 14 2025 - 16:08:02 -0400)
26

    
27
SoC:   AM62AX SR1.0 HS-FS
28
Model: Critical Link MitySOM-AM62A
29
MitySOM-62x - Model No: 62A74-TX-XAE-RI Serial No: 24008068 Part Number: 80-001736RI-2A
30
DRAM:  Limiting LPDDR4 for ECC
31
3.5 GiB
32
Core:  107 devices, 31 uclasses, devicetree: separate
33
MMC:   mmc@fa10000: 0, mmc@fa00000: 1
34
Loading Environment from FAT... Unable to read "uboot.env" from mmc1:1... 
35
Loading Environment from MMC... OK
36
In:    serial@2800000
37
Out:   serial@2800000
38
Err:   serial@2800000
39
Net:   eth0: ethernet@8000000port@1, eth1: ethernet@8000000port@2
40
Hit any key to stop autoboot:  2  1  0 
41
switch to partitions #0, OK
42
mmc1 is current device
43
SD/MMC found on device 1
44
574 bytes read in 34 ms (15.6 KiB/s)
45
Loaded env from uEnv.txt
46
Importing environment from mmc1 ...
47
53172 bytes read in 46 ms (1.1 MiB/s)
48
Warning: Did not detect image signing certificate. Skipping authentication to prevent boot failure. This will fail on Security Enforcing(HS-SE) devices
49
Load Remote Processor 0 with data@addr=0x82000000 53172 bytes: Success!
50
8391984 bytes read in 57 ms (140.4 MiB/s)
51
Warning: Did not detect image signing certificate. Skipping authentication to prevent boot failure. This will fail on Security Enforcing(HS-SE) devices
52
Load Remote Processor 2 with data@addr=0x82000000 8391984 bytes: Success!
53
Failed to load 'rproc'
54
Failed to load 'u-boot'
55
27884032 bytes read in 1123 ms (23.7 MiB/s)
56
68703 bytes read in 39 ms (1.7 MiB/s)
57
Working FDT set to 88000000
58
## Flattened Device Tree blob at 88000000
59
   Booting using the fdt blob at 0x88000000
60
Working FDT set to 88000000
61
   Loading Device Tree to 000000008feec000, end 000000008fffffff ... OK
62
Working FDT set to 8feec000
63

    
64
Starting kernel ...
65

    
66
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
67
[    0.000000] Linux version 6.6.58-g-g7a2fa4c23070 (oe-user@oe-host) (aarch64-oe-linux-gcc (GCC) 13.3.0, GNU ld (GNU Binutils) 2.42.0.20240723) #1 SMP PREEMPT Tue Apr 29 13:30:39 UTC 2025
68
[    0.000000] KASLR disabled due to lack of seed
69
[    0.000000] Machine model: Critical Link MitySOM-AM62A
70
[    0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '')
71
[    0.000000] printk: bootconsole [ns16550a0] enabled
72
[    0.000000] efi: UEFI not found.
73
[    0.000000] Reserved memory: created CMA memory pool at 0x00000000c0000000, size 512 MiB
74
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
75
[    0.000000] OF: reserved mem: 0x00000000c0000000..0x00000000dfffffff (524288 KiB) map reusable linux,cma
76
[    0.000000] OF: reserved mem: 0x0000000080000000..0x000000008007ffff (512 KiB) nomap non-reusable tfa@80000000
77
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000099800000, size 1 MiB
78
[    0.000000] OF: reserved mem: initialized node c7x-dma-memory@99800000, compatible id shared-dma-pool
79
[    0.000000] OF: reserved mem: 0x0000000099800000..0x00000000998fffff (1024 KiB) nomap non-reusable c7x-dma-memory@99800000
80
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000099900000, size 31 MiB
81
[    0.000000] OF: reserved mem: initialized node c7x-memory@99900000, compatible id shared-dma-pool
82
[    0.000000] OF: reserved mem: 0x0000000099900000..0x000000009b7fffff (31744 KiB) nomap non-reusable c7x-memory@99900000
83
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009b800000, size 1 MiB
84
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9b800000, compatible id shared-dma-pool
85
[    0.000000] OF: reserved mem: 0x000000009b800000..0x000000009b8fffff (1024 KiB) nomap non-reusable r5f-dma-memory@9b800000
86
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009b900000, size 15 MiB
87
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9b900000, compatible id shared-dma-pool
88
[    0.000000] OF: reserved mem: 0x000000009b900000..0x000000009c7fffff (15360 KiB) nomap non-reusable r5f-dma-memory@9b900000
89
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009c800000, size 1 MiB
90
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9c800000, compatible id shared-dma-pool
91
[    0.000000] OF: reserved mem: 0x000000009c800000..0x000000009c8fffff (1024 KiB) nomap non-reusable r5f-dma-memory@9c800000
92
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009c900000, size 30 MiB
93
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9c900000, compatible id shared-dma-pool
94
[    0.000000] OF: reserved mem: 0x000000009c900000..0x000000009e6fffff (30720 KiB) nomap non-reusable r5f-dma-memory@9c900000
95
[    0.000000] OF: reserved mem: 0x000000009e800000..0x000000009fffffff (24576 KiB) nomap non-reusable optee@9e800000
96
[    0.000000] OF: reserved mem: 0x00000000a0000000..0x00000000a0ffffff (16384 KiB) nomap non-reusable edgeai-rtos-ipc-memory-region
97
[    0.000000] Reserved memory: created DMA memory pool at 0x00000000a1000000, size 32 MiB
98
[    0.000000] OF: reserved mem: initialized node edgeai-dma-memory@a1000000, compatible id shared-dma-pool
99
[    0.000000] OF: reserved mem: 0x00000000a1000000..0x00000000a2ffffff (32768 KiB) nomap non-reusable edgeai-dma-memory@a1000000
100
[    0.000000] OF: reserved mem: initialized node edgeai_shared-memories, compatible id dma-heap-carveout
101
[    0.000000] OF: reserved mem: 0x00000000a3000000..0x00000000adffffff (180224 KiB) map non-reusable edgeai_shared-memories
102
[    0.000000] Reserved memory: created DMA memory pool at 0x00000000ae000000, size 288 MiB
103
[    0.000000] OF: reserved mem: initialized node edgeai-core-heap-memory@ae000000, compatible id shared-dma-pool
104
[    0.000000] OF: reserved mem: 0x00000000ae000000..0x00000000bfffffff (294912 KiB) nomap non-reusable edgeai-core-heap-memory@ae000000
105
[    0.000000] Zone ranges:
106
[    0.000000]   DMA      [mem 0x0000000080000000-0x00000000ffffffff]
107
[    0.000000]   DMA32    empty
108
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000008dfffffff]
109
[    0.000000] Movable zone start for each node
110
[    0.000000] Early memory node ranges
111
[    0.000000]   node   0: [mem 0x0000000080000000-0x000000008007ffff]
112
[    0.000000]   node   0: [mem 0x0000000080080000-0x00000000997fffff]
113
[    0.000000]   node   0: [mem 0x0000000099800000-0x000000009e6fffff]
114
[    0.000000]   node   0: [mem 0x000000009e700000-0x000000009e7fffff]
115
[    0.000000]   node   0: [mem 0x000000009e800000-0x00000000a2ffffff]
116
[    0.000000]   node   0: [mem 0x00000000a3000000-0x00000000adffffff]
117
[    0.000000]   node   0: [mem 0x00000000ae000000-0x00000000bfffffff]
118
[    0.000000]   node   0: [mem 0x00000000c0000000-0x00000000ffffffff]
119
[    0.000000]   node   0: [mem 0x0000000880000000-0x00000008dfffffff]
120
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000008dfffffff]
121
[    0.000000] psci: probing for conduit method from DT.
122
[    0.000000] psci: PSCIv1.1 detected in firmware.
123
[    0.000000] psci: Using standard PSCI v0.2 function IDs
124
[    0.000000] psci: Trusted OS migration not required
125
[    0.000000] psci: SMC Calling Convention v1.5
126
[    0.000000] percpu: Embedded 29 pages/cpu s81192 r8192 d29400 u118784
127
[    0.000000] Detected VIPT I-cache on CPU0
128
[    0.000000] CPU features: detected: GIC system register CPU interface
129
[    0.000000] CPU features: detected: ARM erratum 845719
130
[    0.000000] alternatives: applying boot alternatives
131
[    0.000000] Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 mtdparts=spi-nand0:512k(ospi_nand.tiboot3),2m(ospi_nand.tispl),4m(ospi_nand.u-boot),256k(ospi_nand.env),256k(ospi_nand.env.backup),98048k@32m(ospi_nand.rootfs),256k@130816k(ospi_nand.phypattern) root=PARTUUID=076c4a2a-02 rw rootfstype=ext4 rootwait
132
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
133
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
134
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 903168
135
[    0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
136
[    0.000000] software IO TLB: area num 4.
137
[    0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB)
138
[    0.000000] Memory: 2350736K/3670016K available (14592K kernel code, 2270K rwdata, 5048K rodata, 5184K init, 470K bss, 794992K reserved, 524288K cma-reserved)
139
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
140
[    0.000000] ftrace: allocating 47819 entries in 187 pages
141
[    0.000000] ftrace: allocated 187 pages with 6 groups
142
[    0.000000] trace event string verifier disabled
143
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
144
[    0.000000] rcu: 	RCU event tracing is enabled.
145
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
146
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
147
[    0.000000] 	Rude variant of Tasks RCU enabled.
148
[    0.000000] 	Tracing variant of Tasks RCU enabled.
149
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
150
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
151
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
152
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
153
[    0.000000] GICv3: 256 SPIs implemented
154
[    0.000000] GICv3: 0 Extended SPIs implemented
155
[    0.000000] Root IRQ handler: gic_handle_irq
156
[    0.000000] GICv3: GICv3 features: 16 PPIs
157
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001880000
158
[    0.000000] ITS [mem 0x01820000-0x0182ffff]
159
[    0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS
160
[    0.000000] ITS@0x0000000001820000: Devices Table too large, reduce ids 20->19
161
[    0.000000] ITS@0x0000000001820000: allocated 524288 Devices @880800000 (flat, esz 8, psz 64K, shr 0)
162
[    0.000000] ITS: using cache flushing for cmd queue
163
[    0.000000] GICv3: using LPI property table @0x00000008801a0000
164
[    0.000000] GIC: using cache flushing for LPI property table
165
[    0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000008801b0000
166
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
167
[    0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys).
168
[    0.000000] clocksource: arch_sys_counter: mask: 0x3ffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns
169
[    0.000001] sched_clock: 58 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns
170
[    0.008647] Console: colour dummy device 80x25
171
[    0.013275] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=800000)
172
[    0.023960] pid_max: default: 32768 minimum: 301
173
[    0.028778] LSM: initializing lsm=capability,selinux,integrity
174
[    0.034770] SELinux:  Initializing.
175
[    0.038474] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
176
[    0.046061] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
177
[    0.056143] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
178
[    0.063481] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
179
[    0.071216] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
180
[    0.079177] rcu: Hierarchical SRCU implementation.
181
[    0.084086] rcu: 	Max phase no-delay instances is 1000.
182
[    0.089734] Platform MSI: msi-controller@1820000 domain created
183
[    0.096111] PCI/MSI: /bus@f0000/interrupt-controller@1800000/msi-controller@1820000 domain created
184
[    0.105601] EFI services will not be available.
185
[    0.110554] smp: Bringing up secondary CPUs ...
186
[    0.115936] Detected VIPT I-cache on CPU1
187
[    0.116029] GICv3: CPU1: found redistributor 1 region 0:0x00000000018a0000
188
[    0.116048] GICv3: CPU1: using allocated LPI pending table @0x00000008801c0000
189
[    0.116106] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
190
[    0.116920] Detected VIPT I-cache on CPU2
191
[    0.116984] GICv3: CPU2: found redistributor 2 region 0:0x00000000018c0000
192
[    0.116999] GICv3: CPU2: using allocated LPI pending table @0x00000008801d0000
193
[    0.117038] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
194
[    0.117723] Detected VIPT I-cache on CPU3
195
[    0.117781] GICv3: CPU3: found redistributor 3 region 0:0x00000000018e0000
196
[    0.117798] GICv3: CPU3: using allocated LPI pending table @0x00000008801e0000
197
[    0.117832] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
198
[    0.117925] smp: Brought up 1 node, 4 CPUs
199
[    0.197672] SMP: Total of 4 processors activated.
200
[    0.202487] CPU features: detected: 32-bit EL0 Support
201
[    0.207764] CPU features: detected: CRC32 instructions
202
[    0.213094] CPU: All CPU(s) started at EL2
203
[    0.217295] alternatives: applying system-wide alternatives
204
[    0.225054] devtmpfs: initialized
205
[    0.239253] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
206
[    0.249266] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
207
[    0.273103] pinctrl core: initialized pinctrl subsystem
208
[    0.279093] DMI not present or invalid.
209
[    0.283747] NET: Registered PF_NETLINK/PF_ROUTE protocol family
210
[    0.290919] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
211
[    0.298292] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
212
[    0.306375] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
213
[    0.314546] audit: initializing netlink subsys (disabled)
214
[    0.320298] audit: type=2000 audit(0.216:1): state=initialized audit_enabled=0 res=1
215
[    0.320836] thermal_sys: Registered thermal governor 'step_wise'
216
[    0.328241] thermal_sys: Registered thermal governor 'power_allocator'
217
[    0.334432] cpuidle: using governor menu
218
[    0.345332] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
219
[    0.352384] ASID allocator initialised with 65536 entries
220
[    0.363877] /bus@f0000/interrupt-controller@1800000: Fixed dependency cycle(s) with /bus@f0000/interrupt-controller@1800000
221
[    0.375422] /bus@f0000/i2c@20010000/tfp410@38: Fixed dependency cycle(s) with /bus@f0000/dss@30200000
222
[    0.385014] /bus@f0000/dss@30200000: Fixed dependency cycle(s) with /bus@f0000/i2c@20010000/tfp410@38
223
[    0.395055] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/mcu-gpio-p3-default-pins
224
[    0.408545] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/mcu-system-default-pins
225
[    0.421898] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/mcu-uart1-default-pins
226
[    0.435159] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/jtag-default-pins
227
[    0.447976] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/mcu_system_pins_default
228
[    0.464947] /bus@f0000/pinctrl@f4000: Fixed dependency cycle(s) with /bus@f0000/pinctrl@f4000/gpio-p3-default-pins
229
[    0.475573] /bus@f0000/pinctrl@f4000: Fixed dependency cycle(s) with /bus@f0000/pinctrl@f4000/main-system-default-pins
230
[    0.487697] /bus@f0000/i2c@20010000/tfp410@38: Fixed dependency cycle(s) with /bus@f0000/dss@30200000
231
[    0.498761] /bus@f0000/pinctrl@a40000: Fixed dependency cycle(s) with /bus@f0000/pinctrl@a40000/cpsw-cpts
232
[    0.510333] /bus@f0000/i2c@20010000/tfp410@38: Fixed dependency cycle(s) with /bus@f0000/dss@30200000
233
[    0.519862] /bus@f0000/dss@30200000: Fixed dependency cycle(s) with /bus@f0000/i2c@20010000/tfp410@38
234
[    0.532996] /bus@f0000/i2c@20010000/tfp410@38: Fixed dependency cycle(s) with /connector-hdmi
235
[    0.541825] /connector-hdmi: Fixed dependency cycle(s) with /bus@f0000/i2c@20010000/tfp410@38
236
[    0.550682] /bus@f0000/dwc3-usb@f900000/usb@31000000: Fixed dependency cycle(s) with /usb_microb_connector
237
[    0.560626] /usb_microb_connector: Fixed dependency cycle(s) with /bus@f0000/dwc3-usb@f900000/usb@31000000
238
[    0.571053] Modules: 25824 pages in range for non-PLT usage
239
[    0.571061] Modules: 517344 pages in range for PLT usage
240
[    0.577705] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
241
[    0.590122] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
242
[    0.596536] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
243
[    0.603477] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
244
[    0.609886] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
245
[    0.616826] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
246
[    0.623236] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
247
[    0.630176] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
248
[    0.638351] k3-chipinfo 43000014.chipid: Family:AM62AX rev:SR1.0 JTAGID[0x0bb8d02f] Detected
249
[    0.649990] iommu: Default domain type: Translated
250
[    0.654924] iommu: DMA domain TLB invalidation policy: strict mode
251
[    0.661705] SCSI subsystem initialized
252
[    0.665990] usbcore: registered new interface driver usbfs
253
[    0.671642] usbcore: registered new interface driver hub
254
[    0.677106] usbcore: registered new device driver usb
255
[    0.682947] pps_core: LinuxPPS API ver. 1 registered
256
[    0.688032] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
257
[    0.697382] PTP clock support registered
258
[    0.701839] EDAC MC: Ver: 3.0.0
259
[    0.705735] scmi_core: SCMI protocol bus registered
260
[    0.711090] FPGA manager framework
261
[    0.714670] Advanced Linux Sound Architecture Driver Initialized.
262
[    0.722233] clocksource: Switched to clocksource arch_sys_counter
263
[    0.728920] VFS: Disk quotas dquot_6.6.0
264
[    0.732974] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
265
[    0.747173] Carveout Heap: Exported 176 MiB at 0x00000000a3000000
266
[    0.753579] NET: Registered PF_INET protocol family
267
[    0.758815] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
268
[    0.769398] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
269
[    0.778250] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
270
[    0.786190] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
271
[    0.794504] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
272
[    0.803167] TCP: Hash tables configured (established 32768 bind 32768)
273
[    0.810073] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
274
[    0.817030] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
275
[    0.824632] NET: Registered PF_UNIX/PF_LOCAL protocol family
276
[    0.831028] RPC: Registered named UNIX socket transport module.
277
[    0.837117] RPC: Registered udp transport module.
278
[    0.841931] RPC: Registered tcp transport module.
279
[    0.846740] RPC: Registered tcp-with-tls transport module.
280
[    0.852351] RPC: Registered tcp NFSv4.1 backchannel transport module.
281
[    0.858948] NET: Registered PF_XDP protocol family
282
[    0.863880] PCI: CLS 0 bytes, default 64
283
[    0.875698] Initialise system trusted keyrings
284
[    0.880580] workingset: timestamp_bits=46 max_order=20 bucket_order=0
285
[    0.887572] squashfs: version 4.0 (2009/01/31) Phillip Lougher
286
[    0.893876] NFS: Registering the id_resolver key type
287
[    0.899084] Key type id_resolver registered
288
[    0.903363] Key type id_legacy registered
289
[    0.907482] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
290
[    0.914338] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
291
[    0.956344] Key type asymmetric registered
292
[    0.960548] Asymmetric key parser 'x509' registered
293
[    0.965605] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
294
[    0.973405] io scheduler mq-deadline registered
295
[    0.978046] io scheduler kyber registered
296
[    0.982187] io scheduler bfq registered
297
[    0.989871] pinctrl-single 4084000.pinctrl: 34 pins, size 136
298
[    0.996632] pinctrl-single f4000.pinctrl: 151 pins, size 604
299
[    1.004326] pinctrl-single a40000.pinctrl: 512 pins, size 2048
300
[    1.018133] Serial: 8250/16550 driver, 12 ports, IRQ sharing enabled
301
[    1.037660] loop: module loaded
302
[    1.042263] megasas: 07.725.01.00-rc1
303
[    1.050366] tun: Universal TUN/TAP device driver, 1.6
304
[    1.056856] VFIO - User Level meta-driver version: 0.3
305
[    1.063557] usbcore: registered new interface driver usb-storage
306
[    1.070579] i2c_dev: i2c /dev entries driver
307
[    1.076963] sdhci: Secure Digital Host Controller Interface driver
308
[    1.083327] sdhci: Copyright(c) Pierre Ossman
309
[    1.088075] sdhci-pltfm: SDHCI platform and OF driver helper
310
[    1.094843] ledtrig-cpu: registered to indicate activity on CPUs
311
[    1.101396] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
312
[    1.108773] usbcore: registered new interface driver usbhid
313
[    1.114493] usbhid: USB HID core driver
314
[    1.120055] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
315
[    1.129411] optee: probing for conduit method.
316
[    1.134010] optee: revision 4.4 (8f645256efc0dc66)
317
[    1.134497] optee: dynamic shared memory is enabled
318
[    1.145218] random: crng init done
319
[    1.148825] optee: initialized driver
320
[    1.154799] Initializing XFRM netlink socket
321
[    1.159226] NET: Registered PF_PACKET protocol family
322
[    1.164477] Key type dns_resolver registered
323
[    1.177897] registered taskstats version 1
324
[    1.182294] Loading compiled-in X.509 certificates
325
[    1.199601] ti-sci 44043000.system-controller: ABI: 4.0 (firmware rev 0x000a '10.1.8--v10.01.08 (Fiery Fox)')
326
[    1.252849] /bus@f0000/i2c@20000000/pmic@30: Fixed dependency cycle(s) with /bus@f0000/i2c@20000000/pmic@30/regulators/buck2
327
[    1.287223] omap_i2c 20000000.i2c: bus 0 rev0.12 at 400 kHz
328
[    1.294755] /connector-hdmi: Fixed dependency cycle(s) with /bus@f0000/i2c@20010000/tfp410@38
329
[    1.303569] /bus@f0000/dss@30200000: Fixed dependency cycle(s) with /bus@f0000/i2c@20010000/tfp410@38
330
[    1.313063] /bus@f0000/i2c@20010000/tfp410@38: Fixed dependency cycle(s) with /connector-hdmi
331
[    1.321846] /bus@f0000/i2c@20010000/tfp410@38: Fixed dependency cycle(s) with /bus@f0000/dss@30200000
332
[    1.331610] omap_i2c 20010000.i2c: bus 1 rev0.12 at 100 kHz
333
[    1.337843] ti-sci-intr 4210000.interrupt-controller: Interrupt Router 5 domain created
334
[    1.346231] ti-sci-intr bus@f0000:interrupt-controller@a00000: Interrupt Router 3 domain created
335
[    1.355506] ti-sci-inta 48000000.interrupt-controller: Interrupt Aggregator domain 28 created
336
[    1.364644] ti-sci-inta 4e0a0000.interrupt-controller: Interrupt Aggregator domain 200 created
337
[    1.374528] ti-udma 485c0100.dma-controller: Number of rings: 82
338
[    1.383584] ti-udma 485c0100.dma-controller: Channels: 48 (bchan: 18, tchan: 12, rchan: 18)
339
[    1.395233] ti-udma 485c0000.dma-controller: Number of rings: 150
340
[    1.406832] ti-udma 485c0000.dma-controller: Channels: 35 (tchan: 20, rchan: 15)
341
[    1.416667] ti-udma 4e230000.dma-controller: Number of rings: 6
342
[    1.423391] ti-udma 4e230000.dma-controller: Channels: 6 (bchan: 0, tchan: 0, rchan: 6)
343
[    1.433217] printk: console [ttyS2] disabled
344
[    1.438038] 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 248, base_baud = 3000000) is a 8250
345
[    1.446941] printk: console [ttyS2] enabled
346
[    1.446941] printk: console [ttyS2] enabled
347
[    1.455530] printk: bootconsole [ns16550a0] disabled
348
[    1.455530] printk: bootconsole [ns16550a0] disabled
349
[    1.469105] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
350
[    1.514240] davinci_mdio 8000f00.mdio: davinci mdio revision 9.7, bus freq 1000000
351
[    1.530290] davinci_mdio 8000f00.mdio: phy[3]: device 8000f00.mdio:03, driver Microchip KSZ9131 Gigabit PHY
352
[    1.540048] davinci_mdio 8000f00.mdio: phy[4]: device 8000f00.mdio:04, driver Microchip KSZ9131 Gigabit PHY
353
[    1.549823] am65-cpsw-nuss 8000000.ethernet: initializing am65 cpsw nuss version 0x6BA01103, cpsw version 0x6BA81103 Ports: 3 quirks:00000006
354
[    1.562714] am65-cpsw-nuss 8000000.ethernet: initialized cpsw ale version 1.5
355
[    1.569849] am65-cpsw-nuss 8000000.ethernet: ALE Table size 512
356
[    1.576369] pps pps0: new PPS source ptp0
357
[    1.580707] am65-cpsw-nuss 8000000.ethernet: CPTS ver 0x4e8a010c, freq:500000000, add_val:1 pps:1
358
[    1.595130] am65-cpsw-nuss 8000000.ethernet: set new flow-id-base 19
359
[    1.605907] /usb_microb_connector: Fixed dependency cycle(s) with /bus@f0000/dwc3-usb@f900000/usb@31000000
360
[    1.615800] /bus@f0000/dwc3-usb@f900000/usb@31000000: Fixed dependency cycle(s) with /usb_microb_connector
361
[    1.628639] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
362
[    1.634225] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
363
[    1.642026] xhci-hcd xhci-hcd.0.auto: USB3 root hub has no ports
364
[    1.648036] xhci-hcd xhci-hcd.0.auto: hcc params 0x0258fe6d hci version 0x110 quirks 0x0000008020000010
365
[    1.657489] xhci-hcd xhci-hcd.0.auto: irq 263, io mem 0x31100000
366
[    1.664480] hub 1-0:1.0: USB hub found
367
[    1.668313] hub 1-0:1.0: 1 port detected
368
[    1.676135] core: _opp_supported_by_regulators: OPP minuV: 850000 maxuV: 850000, not supported by regulator
369
[    1.685917] cpu cpu0: _opp_add: OPP not supported by regulators (1400000000)
370
[    1.693795] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1200000 KHz, changing to: 1250000 KHz
371
[    1.706485] mmc0: CQHCI version 5.10
372
[    1.719506] input: tps65219-pwrbutton as /devices/platform/bus@f0000/20000000.i2c/i2c-0/0-0030/tps65219-pwrbutton.3.auto/input/input0
373
[    1.732884] pca953x 1-0020: supply vcc not found, using dummy regulator
374
[    1.739917] pca953x 1-0020: using no AI
375
[    1.748929] mmc0: SDHCI controller on fa10000.mmc [fa10000.mmc] using ADMA 64-bit
376
[    1.775319] mmc1: CQHCI version 5.10
377
[    1.779995] clk: Disabling unused clocks
378
[    1.788188] ALSA device list:
379
[    1.791182]   No soundcards found.
380
[    1.803375] mmc0: Command Queue Engine enabled
381
[    1.807867] mmc0: new HS200 MMC card at address 0001
382
[    1.813533] mmcblk0: mmc0:0001 IY2964 58.3 GiB
383
[    1.816848] mmc1: SDHCI controller on fa00000.mmc [fa00000.mmc] using ADMA 64-bit
384
[    1.821294]  mmcblk0: p1
385
[    1.828726] mmcblk0boot0: mmc0:0001 IY2964 4.00 MiB
386
[    1.834781] mmcblk0boot1: mmc0:0001 IY2964 4.00 MiB
387
[    1.840641] mmcblk0rpmb: mmc0:0001 IY2964 4.00 MiB, chardev (239:0)
388
[    1.847109] Waiting for root device PARTUUID=076c4a2a-02...
389
[    1.872715] mmc1: new ultra high speed SDR104 SDHC card at address 0001
390
[    1.880204] mmcblk1: mmc1:0001 GB1QT 29.8 GiB
391
[    1.886544]  mmcblk1: p1 p2
392
[    1.934304] usb 1-1: new high-speed USB device number 2 using xhci-hcd
393
[    2.103535] EXT4-fs (mmcblk1p2): recovery complete
394
[    2.110327] EXT4-fs (mmcblk1p2): mounted filesystem 7a42c496-886b-4258-91fe-846c957a0da8 r/w with ordered data mode. Quota mode: none.
395
[    2.122545] VFS: Mounted root (ext4 filesystem) on device 179:98.
396
[    2.129374] devtmpfs: mounted
397
[    2.136081] Freeing unused kernel memory: 5184K
398
[    2.140842] Run /sbin/init as init process
399
[    2.144154] hub 1-1:1.0: USB hub found
400
[    2.148812] hub 1-1:1.0: 2 ports detected
401
[    2.322885] systemd[1]: System time before build time, advancing clock.
402
[    2.367818] NET: Registered PF_INET6 protocol family
403
[    2.374040] Segment Routing with IPv6
404
[    2.377779] In-situ OAM (IOAM) with IPv6
405
[    2.412389] systemd[1]: systemd 255.13^ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
406
[    2.444330] systemd[1]: Detected architecture arm64.
407

    
408
Welcome to Arago 2023.10!
409

    
410

    
411
[    2.463195] systemd[1]: Hostname set to <mitysom-am62ax>.
412
[    2.872400] systemd[1]: /etc/systemd/system/sync-clocks.service:11: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
413
[    2.967095] systemd[1]: Queued start job for default target Multi-User System.
414
[    3.013337] systemd[1]: Created slice Slice /system/getty.
415
[  OK  ] Created slice Slice /system/getty.
416

    
417
[    3.037248] systemd[1]: Created slice Slice /system/modprobe.
418
[  OK  ] Created slice Slice /system/modprobe.
419

    
420
[    3.061088] systemd[1]: Created slice Slice /system/serial-getty.
421
[  OK  ] Created slice Slice /system/serial-getty.
422

    
423
[    3.084418] systemd[1]: Created slice User and Session Slice.
424
[  OK  ] Created slice User and Session Slice.
425

    
426
[    3.106800] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
427
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
428

    
429
[    3.130668] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
430
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
431

    
432
[    3.154448] systemd[1]: Expecting device /dev/fb0...
433
         Expecting device /dev/fb0...
434

    
435
[    3.174357] systemd[1]: Expecting device /dev/ttyS2...
436
         Expecting device /dev/ttyS2...
437

    
438
[    3.190526] systemd[1]: Reached target Path Units.
439
[  OK  ] Reached target Path Units.
440

    
441
[    3.206401] systemd[1]: Reached target Remote File Systems.
442
[  OK  ] Reached target Remote File Systems.
443

    
444
[    3.226366] systemd[1]: Reached target Slice Units.
445
[  OK  ] Reached target Slice Units.
446

    
447
[    3.242362] systemd[1]: Reached target Swaps.
448
[  OK  ] Reached target Swaps.
449

    
450
[    3.302035] systemd[1]: Listening on RPCbind Server Activation Socket.
451
[  OK  ] Listening on RPCbind Server Activation Socket.
452

    
453
[    3.326616] systemd[1]: Reached target RPC Port Mapper.
454
[  OK  ] Reached target RPC Port Mapper.
455

    
456
[    3.354092] systemd[1]: Listening on Process Core Dump Socket.
457
[  OK  ] Listening on Process Core Dump Socket.
458

    
459
[    3.374981] systemd[1]: Listening on initctl Compatibility Named Pipe.
460
[  OK  ] Listening on initctl Compatibility Named Pipe.
461

    
462
[    3.399925] systemd[1]: Listening on Journal Audit Socket.
463
[  OK  ] Listening on Journal Audit Socket.
464

    
465
[    3.423304] systemd[1]: Listening on Journal Socket (/dev/log).
466
[  OK  ] Listening on Journal Socket (/dev/log).
467

    
468
[    3.447276] systemd[1]: Listening on Journal Socket.
469
[  OK  ] Listening on Journal Socket.
470

    
471
[    3.467426] systemd[1]: Listening on Network Service Netlink Socket.
472
[  OK  ] Listening on Network Service Netlink Socket.
473

    
474
[    3.492292] systemd[1]: Listening on udev Control Socket.
475
[  OK  ] Listening on udev Control Socket.
476

    
477
[    3.515141] systemd[1]: Listening on udev Kernel Socket.
478
[  OK  ] Listening on udev Kernel Socket.
479

    
480
[    3.539233] systemd[1]: Listening on User Database Manager Socket.
481
[  OK  ] Listening on User Database Manager Socket.
482

    
483
[    3.586859] systemd[1]: Mounting Huge Pages File System...
484
         Mounting Huge Pages File System...
485

    
486
[    3.598074] systemd[1]: Mounting POSIX Message Queue File System...
487
         Mounting POSIX Message Queue File System...
488

    
489
[    3.628165] systemd[1]: Mounting Kernel Debug File System...
490
         Mounting Kernel Debug File System...
491

    
492
[    3.652132] systemd[1]: Mounting Kernel Trace File System...
493
         Mounting Kernel Trace File System...
494

    
495
[    3.709192] systemd[1]: Mounting Temporary Directory /tmp...
496
         Mounting Temporary Directory /tmp...
497

    
498
[    3.733693] systemd[1]: Starting Create List of Static Device Nodes...
499
         Starting Create List of Static Device Nodes...
500

    
501
[    3.768663] systemd[1]: Starting Load Kernel Module configfs...
502
         Starting Load Kernel Module configfs...
503

    
504
[    3.796494] systemd[1]: Starting Load Kernel Module drm...
505
         Starting Load Kernel Module drm...
506

    
507
[    3.820389] systemd[1]: Starting Load Kernel Module fuse...
508
         Starting Load Kernel Module fuse...
509

    
510
[    3.849865] systemd[1]: Starting RPC Bind...
511
         Starting RPC Bind...
512

    
513
[    3.867025] fuse: init (API version 7.39)
514
[    3.871759] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/).
515
[    3.927616] systemd[1]: Starting Journal Service...
516
         Starting Journal Service...
517

    
518
[    3.956222] systemd[1]: Starting Load Kernel Modules...
519
         Starting Load Kernel Modules...
520

    
521
[    3.985613] systemd[1]: Starting Generate network units from Kernel command line...
522
         Starting Generate network units from Kernel command line...
523

    
524
[    4.018921] systemd[1]: Starting Remount Root and Kernel File Systems...
525
[    4.020030] cryptodev: loading out-of-tree module taints kernel.
526
         Starting Remount Root and Kernel File Systems[    4.034575] cryptodev: driver 1.14 loaded.
527
[0m...
528

    
529
[    4.041482] systemd-journald[127]: Collecting audit messages is enabled.
530
[    4.056808] systemd[1]: Starting Coldplug All udev Devices...
531
         Starting Coldplug All udev Devices...
532

    
533
[    4.095627] systemd[1]: Started RPC Bind.
534
[  OK  ] Started RPC Bind.
535

    
536
[    4.111279] EXT4-fs (mmcblk1p2): re-mounted 7a42c496-886b-4258-91fe-846c957a0da8 r/w. Quota mode: none.
537
[    4.126070] systemd[1]: Mounted Huge Pages File System.
538
[  OK  ] Mounted Huge Pages File System.
539

    
540
[    4.151364] systemd[1]: Started Journal Service.
541
[  OK  ] Started Journal Service.
542

    
543
[  OK  ] Mounted POSIX Message Queue File System.
544

    
545
[  OK  ] Mounted Kernel Debug File System.
546

    
547
[  OK  ] Mounted Kernel Trace File System.
548

    
549
[  OK  ] Mounted Temporary Directory /tmp.
550

    
551
[  OK  ] Finished Create List of Static Device Nodes.
552

    
553
[  OK  ] Finished Load Kernel Module configfs.
554

    
555
[  OK  ] Finished Load Kernel Module drm.
556

    
557
[  OK  ] Finished Load Kernel Module fuse.
558

    
559
[  OK  ] Finished Load Kernel Modules.
560

    
561
[  OK  ] Finished Generate network units from Kernel command line.
562

    
563
[  OK  ] Finished Remount Root and Kernel File Systems.
564

    
565
         Mounting FUSE Control File System...
566

    
567
         Mounting Kernel Configuration File System...
568

    
569
         Starting Flush Journal to Persistent Storage...
570

    
571
         Starting Apply Kernel Variables...
572

    
573
         Starting Create Static Device Nodes in /dev gr[    4.565643] systemd-journald[127]: Received client request to flush runtime journal.
574
acefully...
575

    
576
[  OK  ] Mounted FUSE Control File System.
577

    
578
[  OK  ] Mounted Kernel Configuration File System.
579

    
580
[  OK  ] Finished Flush Journal to Persistent Storage.
581

    
582
[  OK  ] Finished Apply Kernel Variables.
583

    
584
[  OK  ] Finished Create Static Device Nodes in /dev gracefully.
585

    
586
         Starting Create Static Device Nodes in /dev...
587

    
588
[  OK  ] Finished Create Static Device Nodes in /dev.
589

    
590
[  OK  ] Reached target Preparation for Local File Systems.
591

    
592
         Mounting /var/volatile...
593

    
594
[    4.909800] audit: type=1334 audit(1728487094.580:2): prog-id=6 op=LOAD
595
[    4.916597] audit: type=1334 audit(1728487094.588:3): prog-id=7 op=LOAD
596
         Starting Rule-based Manager for Device Events and Files...
597

    
598
[  OK  ] Finished Coldplug All udev Devices.
599

    
600
[  OK  ] Mounted /var/volatile.
601

    
602
         Starting Load/Save OS Random Seed...
603

    
604
[  OK  ] Reached target Local File Systems.
605

    
606
         Starting Create System Files and Directories...
607

    
608
[  OK  ] Finished Load/Save OS Random Seed.
609

    
610
[  OK  ] Finished Create System Files and Directories.
611

    
612
[    5.170985] audit: type=1334 audit(1728487094.844:4): prog-id=8 op=LOAD
613
         Starting Network Name Resolution...
614

    
615
[    5.211252] audit: type=1334 audit(1728487094.884:5): prog-id=9 op=LOAD
616
         Starting Network Time Synchronization...
617

    
618
         Starting Record System Boot/Shutdown in UTMP...
619

    
620
[    5.279060] audit: type=1334 audit(1728487094.952:6): prog-id=10 op=LOAD
621
[    5.285930] audit: type=1334 audit(1728487094.956:7): prog-id=11 op=LOAD
622
[    5.292883] audit: type=1334 audit(1728487094.964:8): prog-id=12 op=LOAD
623
         Starting User Database Manager...
624

    
625
[  OK  ] Finished Record System Boot/Shutdown in UTMP.
626

    
627
[  OK  ] Started User Database Manager.
628

    
629
[  OK  ] Started Rule-based Manager for Device Events and Files.
630

    
631
[  OK  ] Found device /dev/ttyS2.
632

    
633
[  OK  ] Started Network Time Synchronization.
634

    
635
[  OK  ] Reached target System Time Set.
636

    
637
[  OK  ] Started Network Name Resolution.
638

    
639
[  OK  ] Reached target Host and Network Name Lookups.
640

    
641
[  OK  ] Reached target System Initialization.
642

    
643
[  OK  ] Started Daily Cleanup of Temporary Directories.
644

    
645
[  OK  ] Reached target Timer Units.
646

    
647
[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
648

    
649
[  OK  ] Listening on D-Bus System Message Bus Socket.
650

    
651
         Starting Docker Socket for the API...
652

    
653
[  OK  ] Listening on dropbear.socket.
654

    
655
[    6.057637] audit: type=1334 audit(1747254604.351:9): prog-id=13 op=LOAD
656
         Starting D-Bus System Message Bus...
657

    
658
[  OK  ] Listening on Docker Socket for the API.
659

    
660
[  OK  ] Started D-Bus System Message Bus.
661

    
662
[    6.257342] dbus-broker-lau[286]: memfd_create() called without MFD_EXEC or MFD_NOEXEC_SEAL set
663
[  OK  ] Reached target Socket Units.
664

    
665
[  OK  ] Reached target Basic System.
666

    
667
         Starting Avahi mDNS/DNS-SD Stack...
668

    
669
         Starting Print notice about GPLv3 packages...
670

    
671
         Starting IPv6 Packet Filtering Framework...
672

    
673
         Starting IPv4 Packet Filtering Framework...
674

    
675
         Starting Expand the rootfs partiti…to full size of the boot device....
676

    
677
[    6.472579] audit: type=1334 audit(1747254604.767:10): prog-id=14 op=LOAD
678
[    6.479840] audit: type=1334 audit(1747254604.775:11): prog-id=15 op=LOAD
679
[    6.488317] audit: type=1334 audit(1747254604.783:12): prog-id=16 op=LOAD
680
         Starting User Login Management...
681

    
682
         Starting Telnet Server...
683

    
684
[  OK  ] Finished IPv6 Packet Filtering Framework.
685

    
686
[  OK  ] Finished IPv4 Packet Filtering Framework.
687

    
688
[  OK  ] Finished Telnet Server.
689

    
690
[  OK  ] Reached target Preparation for Network.
691

    
692
[    6.618199] audit: type=1334 audit(1747254604.911:13): prog-id=17 op=LOAD
693
         Starting Network Configuration...
694

    
695
[  OK  ] Started Avahi mDNS/DNS-SD Stack.
696

    
697
[  OK  ] Finished Expand the rootfs partition to full size of the boot device..
698

    
699
[  OK  ] Started User Login Management.
700

    
701
[    7.111688] cfg80211: Loading compiled-in X.509 certificates for regulatory database
702
[    7.121435] omap-mailbox 29000000.mailbox: omap mailbox rev 0x66fca100
703
[    7.128960] omap-mailbox 29010000.mailbox: omap mailbox rev 0x66fca100
704
[    7.138521] at24 0-0050: supply vcc not found, using dummy regulator
705
[    7.141665] omap-mailbox 29020000.mailbox: omap mailbox rev 0x66fca100
706
[    7.147812] at24 0-0050: 4096 byte 24c32 EEPROM, read-only
707
[    7.153140] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
708
[    7.157402] omap-mailbox 29030000.mailbox: no available mbox devices found
709
[    7.165981] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
710
[    7.206021] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
711
[    7.214945] cfg80211: failed to load regulatory.db
712
[    7.246709] mc: Linux media interface: v0.10
713
[    7.327905] platform 79000000.r5f: configured R5F for IPC-only mode
714
[    7.334641] platform 79000000.r5f: assigned reserved memory node r5f-dma-memory@9b800000
715
[    7.339719] videodev: Linux video capture interface: v2.00
716
[  OK  ] Started Network Configuration.
717
[    7.349829] remoteproc remoteproc0: 79000000.r5f is available
718

    
719
[  OK  ] Reached target Network.
720
[    7.360280] remoteproc remoteproc0: attaching to 79000000.r5f
721

    
722
[    7.372864] k3-dsp-rproc 7e000000.dsp: assigned reserved memory node c7x-dma-memory@99800000
723
[    7.383086] k3-dsp-rproc 7e000000.dsp: configured DSP for IPC-only mode
724
[    7.395243] remoteproc remoteproc1: 7e000000.dsp is available
725
[    7.395563] rproc-virtio rproc-virtio.4.auto: assigned reserved memory node r5f-dma-memory@9b800000
726
[    7.401366] remoteproc remoteproc1: attaching to 7e000000.dsp
727
[    7.411197] virtio_rpmsg_bus virtio0: rpmsg host is online
728
[    7.416353] virtio_rpmsg_bus virtio0: creating channel ti.ipc4.ping-pong addr 0xd
729
[    7.423438] rproc-virtio rproc-virtio.4.auto: registered virtio0 (type 7)
730
[    7.429891] virtio_rpmsg_bus virtio0: creating channel rpmsg_chrdev addr 0xe
731
[    7.436807] remoteproc remoteproc0: remote processor 79000000.r5f is now attached
732
[    7.463007] rproc-virtio rproc-virtio.5.auto: assigned reserved memory node c7x-dma-memory@99800000
733
[    7.471785] am65-cpsw-nuss 8000000.ethernet eth0: PHY [8000f00.mdio:03] driver [Microchip KSZ9131 Gigabit PHY] (irq=POLL)
734
[    7.486633] am65-cpsw-nuss 8000000.ethernet eth0: configuring for phy/rgmii-rxid link mode
735
[    7.488991] virtio_rpmsg_bus virtio1: rpmsg host is online
736
[    7.500826] virtio_rpmsg_bus virtio1: creating channel ti.ipc4.ping-pong addr 0xd
737
[    7.501129] virtio_rpmsg_bus virtio1: creating channel rpmsg_chrdev addr 0xe
738
[    7.501612] rproc-virtio rproc-virtio.5.auto: registered virtio1 (type 7)
739
[    7.501630] remoteproc remoteproc1: remote processor 7e000000.dsp is now attached
740
[    7.515432] platform 78000000.r5f: R5F core may have been powered on by a different host, programmed state (0) != actual state (1)
741
         Starting containerd container runtime...
742
[    7.549942] platform 78000000.r5f: configured R5F for IPC-only mode
743

    
744
[    7.560314] platform 78000000.r5f: assigned reserved memory node r5f-dma-memory@9c800000
745
[    7.583490] remoteproc remoteproc2: 78000000.r5f is available
746
[    7.589555] remoteproc remoteproc2: attaching to 78000000.r5f
747
[    7.601217] rproc-virtio rproc-virtio.7.auto: assigned reserved memory node r5f-dma-memory@9c800000
748
[    7.629097] am65-cpsw-nuss 8000000.ethernet eth1: PHY [8000f00.mdio:04] driver [Microchip KSZ9131 Gigabit PHY] (irq=POLL)
749
[    7.632955] virtio_rpmsg_bus virtio2: rpmsg host is online
750
[    7.640201] am65-cpsw-nuss 8000000.ethernet eth1: configuring for phy/rgmii-rxid link mode
751
[    7.640201] virtio_rpmsg_bus virtio2: creating channel rpmsg_chrdev addr 0xd
752
[    7.657994] rproc-virtio rproc-virtio.7.auto: registered virtio2 (type 7)
753
[    7.668248] remoteproc remoteproc2: remote processor 78000000.r5f is now attached
754
         Starting LLDP daemon...
755

    
756
[    7.683174] vdec 30210000.video-codec: error -ENXIO: IRQ index 0 not found
757
[    7.690188] vdec 30210000.video-codec: failed to get irq resource, falling back to polling
758
[    7.697636] rtc-ti-k3 2b1f0000.rtc: registered as rtc0
759
[    7.698977] vdec 30210000.video-codec: OPP table not found in device tree
760
[    7.703897] rtc-ti-k3 2b1f0000.rtc: setting system clock to 1970-01-01T00:00:18 UTC (18)
761
[    7.741987] vdec 30210000.video-codec: Added wave5 driver with caps: 'ENCODE' 'DECODE'
762
[    7.751888] vdec 30210000.video-codec: Product Code:      0x521c
763
[    7.758411] vdec 30210000.video-codec: Firmware Revision: 334314
764
[    7.779441] [drm] Initialized tidss 1.0.0 20180215 for 30200000.dss on minor 0
765
[    7.791394] tidss 30200000.dss: [drm] Cannot find any crtc or sizes
766
[  OK  ] Started Netperf Benchmark Server[0[    7.802333] tidss 30200000.dss: [drm] Cannot find any crtc or sizes
767
m.
768

    
769
[    7.826598] systemd-journald[127]: Time jumped backwards, rotating.
770
         Starting Permit User Sessions...
771

    
772
[  OK  ] Reached target Hardware activated USB gadget.
773

    
774
[  OK  ] Finished Permit User Sessions.
775

    
776
[    8.000656] e5010 fd20000.jpeg-encoder: Device registered as /dev/video2
777
[  OK  ] Started Getty on tty1.
778

    
779
[  OK  ] Started Serial Getty on ttyS2.
780

    
781
[  OK  ] Reached target Login Prompts.
782

    
783
         Starting Synchronize System and HW clocks...
784

    
785
[  OK  ] Started LLDP daemon.
786

    
787
[  OK  ] Finished Synchronize System and HW clocks.
788

    
789
[  OK  ] Created slice Slice /system/tee-supplicant.
790

    
791
[  OK  ] Started TEE Supplicant on teepriv0.
792

    
793
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
794

    
795
         Starting Virtual Console Setup...
796

    
797
[  OK  ] Finished Virtual Console Setup.
798

    
799
[    8.744275] cdns-csi2rx: probe of 30101000.csi-bridge failed with error -22
800
[  OK  ] Created slice Slice /system/systemd-fsck.
801

    
802
         Expecting device /dev/mmcblk1p1...
803

    
804
         Starting Save/Restore Sound Card State...
805

    
806
[  OK  ] Finished Save/Restore Sound Card State.
807

    
808
[  OK  ] Reached target Sound Card.
809

    
810
[  OK  ] Found device /dev/mmcblk1p1.
811

    
812
         Starting File System Check on /dev/mmcblk1p1...
813

    
814
[  OK  ] Finished File System Check on /dev/mmcblk1p1.
815

    
816
         Mounting /run/media/boot-mmcblk1p1...
817

    
818
[  OK  ] Mounted /run/media/boot-mmcblk1p1.
819

    
820
***************************************************************
821
***************************************************************
822
NOTICE: This file system contains the following GPL-3.0 packages:
823
	bash
824
	cifs-utils
825
	dosfstools
826
	grub-common
827
	grub-editenv
828
	grub-efi
829
	kbd-keymaps-pine
830
	less
831
	libdw1
832
	libelf1
833
	libgcc1
834
	libreadline8
835
	libstdc++6
836
	parted
837
	rsync
838

    
839
If you do not wish to distribute GPL-3.0 components please remove
840
the above packages prior to distribution.  This can be done using
841
the opkg remove command.  i.e.:
842
    opkg remove <package>
843
Where <package> is the name printed in the list above
844

    
845
NOTE: If the package is a dependency of another package you
846
      will be notified of the dependent packages.  You should
847
      use the --force-removal-of-dependent-packages option to
848
      also remove the dependent packages as well
849
***************************************************************
850
***************************************************************
851
[  OK  ] Finished Print notice about GPLv3 packages.
852

    
853
[  OK  ] Started containerd container runtime.
854

    
855
[  OK  ] Reached target Multi-User System.
856

    
857
         Starting Record Runlevel Change in UTMP...
858

    
859
[  OK  ] Finished Record Runlevel Change in UTMP.
860

    
861
[   11.591761] am65-cpsw-nuss 8000000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
862

    
863

    
864
 _____                    _____           _         _   
865
|  _  |___ ___ ___ ___   |  _  |___ ___  |_|___ ___| |_ 
866
|     |  _| .'| . | . |  |   __|  _| . | | | -_|  _|  _|
867
|__|__|_| |__,|_  |___|  |__|  |_| |___|_| |___|___|_|  
868
              |___|                    |___|            
869

    
870
Arago Project mitysom-am62ax ttyS2
871

    
872
Arago 2023.10 mitysom-am62ax ttyS2
873

    
874
mitysom-am62ax login: root
875

    
876
[   15.753905] audit: type=1006 audit(26.544:14): pid=581 uid=0 subj=kernel old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1
877
[   15.766798] audit: type=1300 audit(26.544:14): arch=c00000b7 syscall=64 success=yes exit=1 a0=8 a1=ffffc1fe8a28 a2=1 a3=1 items=0 ppid=1 pid=581 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="(systemd)" exe="/usr/lib/systemd/systemd-executor" subj=kernel key=(null)
878
[   15.793699] audit: type=1327 audit(26.544:14): proctitle="(systemd)"
879
[   15.819643] audit: type=1334 audit(26.612:15): prog-id=18 op=LOAD
880
[   15.825809] audit: type=1300 audit(26.612:15): arch=c00000b7 syscall=280 success=yes exit=8 a0=5 a1=ffffccdcbed8 a2=90 a3=0 items=0 ppid=1 pid=581 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="systemd" exe="/usr/lib/systemd/systemd" subj=kernel key=(null)
881
[   15.851942] audit: type=1327 audit(26.612:15): proctitle="(systemd)"
882
[   15.858384] audit: type=1334 audit(26.612:16): prog-id=18 op=UNLOAD
883
[   15.864723] audit: type=1300 audit(26.612:16): arch=c00000b7 syscall=57 success=yes exit=0 a0=8 a1=1 a2=0 a3=ffff99e75c60 items=0 ppid=1 pid=581 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="systemd" exe="/usr/lib/systemd/systemd" subj=kernel key=(null)
884
[   15.890668] audit: type=1327 audit(26.612:16): proctitle="(systemd)"
885
[   15.897115] audit: type=1334 audit(26.612:17): prog-id=19 op=LOAD
886

    
887
78root@mitysom-am62ax:~# 
888
root@mitysom-am62ax:~# free
889
              total        used        free      shared  buff/cache   available
890
Mem:        2880208      114112     2629220       10232      136876     2619108
891
Swap:             0           0           0
892
root@mitysom-am62ax:~# memtester 2G
893
memtester version 4.6.0 (64-bit)
894
Copyright (C) 2001-2020 Charles Cazabon.
895
Licensed under the GNU General Public License version 2 (only).
896

    
897
pagesize is 4096
898
pagesizemask is 0xfffffffffffff000
899
want 2048MB (2147483648 bytes)
900
got  2048MB (2147483648 bytes), trying mlock ...locked.
901
Loop 1:
902
  Stuck Address       :            setting   0testing   0setting   1testing   1setting   2testing   2setting   3[   32.006696] UNUSED: disabling
903
testing   3setting   4testing   4setting   5testing   5setting   6testing   6setting   7testing   7setting   8testing   8setting   9testing   9setting  10testing  10setting  11testing  11setting  12testing  12setting  13testing  13setting  14testing  14setting  15testing  15           ok
(4-4/4) Go to top
Add picture from clipboard (Maximum size: 1 GB)