Mity CPU Platforms » MitySOM-5CSX Altera Cyclone V

U-Boot SPL 2019.10-g964a62232a-dirty (Oct 06 2023 - 18:09:56 +0200)

DDRCAL: Scrubbing ECC RAM (1024 MiB).

DDRCAL: SDRAM-ECC initialized success with 608 ms

MPU 800000 kHz

DDR 400000 kHz

EOSC1 25000 kHz

EOSC2 25000 kHz

F2S_SDR_REF 0 kHz

F2S_PER_REF 0 kHz

MMC 50000 kHz

QSPI 400000 kHz

UART 100000 kHz

SPI 200000 kHz

Trying to boot from MMC1

U-Boot 2019.10-g964a62232a-dirty (Oct 06 2023 - 18:09:56 +0200) Critical Link MitySOM-5CSx

CPU: Altera SoCFPGA Platform

FPGA: Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0

BOOT: SD/MMC Internal Transceiver (3.0V)

Model: MitySOM-5CSX-H6-42A Altera SOCFPGA Cyclone V

BOARD: Critical Link MitySOM-5CSx Module

Watchdog enabled

DRAM: 1 GiB

MMC: dwmmc0@ff704000: 0

Loading Environment from MMC... *** Warning - bad CRC, using default environment

In: serial

Out: serial

Err: serial

eeprom_rw_block: Cannot find udev for a bus 0

Error - Failure reading Factory Configuration Version Info

Error - Factory Configuration Invalid

Info - You must set the factory configuration to make permanent

Info - Setting configuration to defaults

Info - Didn't find block

Info - Didn't find block

Bad I2C configuration found

Net:

Warning: ethernet@ff702000 (eth0) using random MAC address - f2:ac:3e:3f:42:73

eth0: ethernet@ff702000

Hit any key to stop autoboot: 0

MitySOM-5CSx # printenv

arch=arm

baudrate=115200

board=mitysom-5cs

board_name=mitysom-5cs

boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}

boot_efi_binary=if fdt addr ${fdt_addr_r}; then bootefi bootmgr ${fdt_addr_r};else bootefi bootmgr ${fdtcontroladdr};fi;load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootarm.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi

boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}

boot_net_usb_start=usb start

boot_prefixes=/ /boot/

boot_script_dhcp=boot.scr.uimg

boot_scripts=boot.scr.uimg boot.scr

boot_syslinux_conf=extlinux/extlinux.conf

boot_targets=mmc0 qspi pxe dhcp

bootcmd=run fatscript; bridge enable; run distro_bootcmd

bootcmd_dhcp=run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00010:UNDI:003000;setenv bootp_arch 0xa;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci;

bootcmd_mmc0=devnum=0; run mmc_boot

bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi

bootcmd_qspi=run qspiload; run qspiboot

bootdelay=2

bootm_size=0xa000000

bootmode=sd

cpu=armv7

distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done

efi_dtb_prefixes=/ /dtb/ /dtb/current/

fatscript=if fatload mmc 0:1 ${scriptaddr} ${scriptfile};then source ${scriptaddr}; fi

fdt_addr_r=0x02000000

fdt_size=0x00010000

fdtcontroladdr=3bf5b740

fdtfile=socfpga_mitysom5csx_devkit.dtb

fpgatype=cv_se_a6

kernel_addr_r=0x01000000

kernel_size=0x005d0000

load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}

loadaddr=0x01000000

mmc_boot=if mmc dev ${devnum}; then devtype=mmc; run scan_dev_for_boot_part; fi

prog_core=if load mmc 0:1 ${loadaddr} fit_spl_fpga.itb;then fpga loadmk 0 ${loadaddr}:fpga-core-1; fi

pxefile_addr_r=0x02200000

qspi_fdt_addr=0x00220000

qspi_kernel_addr=0x00230000

qspiboot=setenv bootargs earlycon root=/dev/mtdblock1 rw rootfstype=jffs2; bootz ${kernel_addr_r} - ${fdt_addr_r}

qspiload=sf probe; sf read ${kernel_addr_r} ${qspi_kernel_addr} ${kernel_size}; sf read ${fdt_addr_r} ${qspi_fdt_addr} ${fdt_size}

ramdisk_addr_r=0x02300000

rtccal=0

scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;

scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done; setenv devplist

scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootarm.efi; then echo Found EFI removable media binary efi/boot/bootarm.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile

scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi

scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done

scriptaddr=0x02100000

scriptfile=u-boot.scr

soc=socfpga

socfpga_legacy_reset_compat=1

stderr=serial

stdin=serial

stdout=serial

usb_boot=usb start; if usb dev ${devnum}; then devtype=usb; run scan_dev_for_boot_part; fi

vendor=cl

ver=U-Boot 2019.10-g964a62232a-dirty (Oct 06 2023 - 18:09:56 +0200) Critical Link MitySOM-5CSx