|
-Boot 2009.11 (Mar 31 2011 - 19:39:18)
|
|
|
|
I2C : ready
|
|
DRAM: 128 MB
|
|
NAND: 256 MiB
|
|
MMC: davinci : 0
|
|
In: serial
|
|
Out: serial
|
|
Err: serial
|
|
ARM Clock : 300000000 Hz
|
|
DDR Clock : 150000000 Hz
|
|
EMIFA CLock : 100000000 Hz
|
|
DSP Clock : 300000000 Hz
|
|
ANSYNC3 Clock : 150000000 Hz
|
|
Enet config : 2
|
|
MMC 0 Enable : 0
|
|
Resetting ethernet phy
|
|
Net: Ethernet PHY: GENERIC @ 0x30 [0x8]
|
|
|
|
Hit any key to stop autoboot: 0
|
|
8192 KiB M25p64 at 0:0 is now current device
|
|
## Booting kernel from Legacy Image at c0700000 ...
|
|
Image Name: Linux-2.6.34-rc1
|
|
Image Type: ARM Linux Kernel Image (uncompressed)
|
|
Data Size: 2203396 Bytes = 2.1 MB
|
|
Load Address: c0008000
|
|
Entry Point: c0008000
|
|
Verifying Checksum ... OK
|
|
Loading Kernel Image ... OK
|
|
OK
|
|
|
|
Starting kernel ...
|
|
|
|
Uncompressing Linux... done, booting the kernel.
|
|
|
|
|
|
...
|
|
|
|
...
|
|
|
|
|
|
spi_davinci spi_davinci.1: DMA: supported
|
|
spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0
|
|
m25p80 spi1.0: m25p64 (8192 Kbytes)
|
|
Creating 8 MTD partitions on "m25p80":
|
|
0x000000000000-0x000000010000 : "ubl"
|
|
0x000000010000-0x000000090000 : "u-boot"
|
|
0x000000090000-0x0000000a0000 : "u-boot-env"
|
|
0x0000000a0000-0x0000000b0000 : "periph-config"
|
|
0x0000000b0000-0x000000100000 : "reserved"
|
|
0x000000100000-0x000000400000 : "kernel"
|
|
0x000000400000-0x000000600000 : "fpga"
|
|
0x000000600000-0x000000800000 : "spare"
|
|
spi_davinci spi_davinci.1: Controller at 0xfef0e000
|
|
CAN device driver interface
|
|
mcp251x spi1.1: probed
|
|
console [netcon0] enabled
|
|
netconsole: network logging started
|
|
ohci_hcd: USB 1.1 'Open Host Controller (OHCI) Driver
|
|
ohci ohci.0 Da8xx OHCI
|
|
ohci ohci.0 new USB bus registered, assigned bus number 1
|
|
Waiting for USB PHY clock good...
|
|
ohci ohc.0: irq 59, io mem 0x01e25000
|
|
hub 1-0:1.0: USB hub found
|
|
hub 1-0:1.0: 1 port detected
|
|
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
|
|
omap_rtc omap_rtc: RTC power up reset detected
|
|
omap_rtc omap_rtc: already running
|
|
i2c /dev entries driver
|
|
cpuidle: using governor ladder
|
|
cpuidle: using governor menu
|
|
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
|
|
usbcore: registered new interface driver usbhid
|
|
usbhid: USB HID core driver
|
|
No device for DAI AK4535
|
|
Cirrus Logic CS4270 ALSA SoC Codec Driver
|
|
No device codec for codec dsd1791
|
|
No device codec for codec DAI dsd1791
|
|
No device codec for codec DAI PCM3008 HiFi
|
|
No device codec for codec DAI SSM2602
|
|
No device codec for codec DAI tlv320aic23
|
|
No device codec for codec DAI UDA134x
|
|
No device codec for codec DAI WM8510 HiFi
|
|
ata1: SATA link down (SStatus 0 SControl 300)
|
|
No device for DAI WM8728
|
|
No device for DAI WM8750
|
|
No device for DAI WM8971
|
|
No device for DAI WM8990 ADC/DAC Primary
|
|
asoc: dsd1791 <-> davinci-i2s mapping ok
|
|
soc-audio soc-audio.0: DSD1791 Audio Codec
|
|
ALSA device list:
|
|
#0: MityDSP-L138 INDIO (dsd1791)
|
|
TCP cubic registered
|
|
NET: Registered protocol family 17
|
|
Can: Controller area network core (rev 20090105 abi 8)
|
|
NET: Registered protocol family 29
|
|
can: raw protocol (rev 20090105)
|
|
Clocks: disable unused i2c1
|
|
Clocks: disable unused emac
|
|
Clocks: disable unused lcdc
|
|
Clocks: disable unused spi0
|
|
Clocks: disable unused mcbsp0
|
|
Clocks: disable unused mcbsp1
|
|
Clocks: disable unused vpif
|
|
Clocks: disable unused ecap
|
|
Clocks: disable unused ehrpwm
|
|
regulator_init_complete: incomplete constraints, leaving LDO2 on
|
|
regulator_init_complete: incomplete constraints, leaving LDO1 on
|
|
regulator_init_complete: incomplete constraints, leaving VDCDC3 on
|
|
regulator_init_complete: incomplete constraints, leaving VDCDC2 on
|
|
regulator_init_complete: incomplete constraints, leaving VDCDC1 on
|
|
emac-mii: probed
|
|
omap_rtc omap_rtc: setting system clock to 2011-05-18 00:38:57 UTC (1305679137)
|
|
Empty flash at 0x045cfe40 ends at 0x045d0000
|
|
jffs2_scan_inode_node(): CRC failed on node at 0x05f0a7f0: Read 0xffffffff, calculated 0x4d5b2912
|
|
Empty flash at 0x05f0a84c ends at 0x05f0b000
|
|
Empty flash at 0x05f1682c ends at 0x05f17000
|
|
Empty flash at 0x0670a958 ends at 0x0670b000
|
|
VFS: Mounted root (jffs2 filesystem) on device 31:0.
|
|
Feeing init memory: 140K
|
|
INIT: Version 2.86 booting
|
|
Please wait: booting...
|
|
Starting udev
|
|
Remounting root file system...
|
|
Caching udev devnodes
|
|
Populating dev cache
|
|
NET: Registered protocol family 10
|
|
Configuring network interfaces... eth0 attached PHY driver [Generic PHY] (mii_b
|
|
us:phy_addr=1:03, id=40005201)
|
|
ADDRCONF (NETDEV_UP): eth0: link is not ready
|
|
udhcpc (v1.13.2) started
|
|
run-parts: /etc/udhcp.d/00avahi-autoipd exited with code 1
|
|
Sending discover...
|
|
PHY: 1:03 - Link is up - 100/Full
|
|
ADDRCONF (NETDEV_CHANGE): eth0: link becomes ready
|
|
Sending discover...
|
|
Sending discover...
|
|
Starting portmap daemon: portmap.
|
|
portmap: fork: No such devicenet.ipv4.conf.default.rp_filter = 1
|
|
net.ipv4.conf.all.rp_filter = 1
|
|
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
|
|
svc: failed to register nfsdv2 RPC service (error 111).
|
|
nfsd: last server has exited, flushing export cache
|
|
JFFS2 notice: (1201) check_node_data: wrong data CRC in data node at 0x0670a6a0:
|
|
read 0x14dd865d, calculated 0x13d965b8
|